18
FN6140.2
June 15, 2006
Absolute Maximum Ratings T
A
= 25°C Thermal Information
Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input, Output or I/O Voltage . . . . . . . . . . . . GND-0.5V to V
CC
+0.5V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Operating Conditions
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to 5.5V
Operating Temperature Range
CMX82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
IMX82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Thermal Resistance (Typical, Note 1) θ
JA
(°C/W)
PLCC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Maximum Storage Temperature Range. . . . . . . . . . -65°C to 150°C
Maximum Junction Temperature
Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Die Characteristics
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 Gates
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
2. θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications V
CC
= 5.0V± 10%; T
A
= Operating Temperature Range
SYMBOL PARAMETER TEST CONDITIONS MIN TYP MAX UNITS
V
IH
Logical One Input Voltage 2.0
2.2
--V
V
IL
Logical Zero Input Voltage - - 0.8 V
V
OH
Logical One Output Voltage I
OH
= -2.5mA,
I
OH
= -100µA
3.0
V
CC
-0.4
--V
V
OL
Logical Zero Output Voltage I
OL
+2.5mA - - 0.4 V
I
I
Input Leakage Current V
IN
= V
CC
or GND, RD, CS, A1, A0, RESET, WR -1.0 - +1.0 µA
IO I/O Pin Leakage Current VO = V
CC
or GND, D0 - D7 -10 - +10 µA
IDAR Darlington Drive Current Ports A, B, C. Test Condition 3 -2.5 - Notes 2, 4 mA
ICCSB Standby Power Supply Current V
CC
= 5.5V, V
IN
= V
CC
or GND. Output Open - - 10 µA
ICCOP Operating Power Supply Current T
A
= +25°C, V
CC
= 5.0V, Typical (See Note 3) - 1 - mA/MHz
NOTES:
3. No internal current limiting exists on Port Outputs. A resistor must be added externally to limit the current.
4. ICCOP = 1mA/MHz of Peripheral Read/Write cycle time. (Example: 1.0µs I/O Read/Write cycle time = 1mA).
5. Tested as V
OH
at -2.5mA.
Capacitance T
A
= 25°C
SYMBOL PARAMETER TYPICAL UNITS TEST CONDITIONS
CIN Input Capacitance 10 pF FREQ = 1MHz, All Measurements are referenced to
device GND
CI/O I/O Capacitance 20 pF
MS82C55A, MQ82C55A, MP82C55A
