NCV890130
http://onsemi.com
4
Figure 3. Pin Connections
1
VIN
SW
2
DRV
3
4
GND
BST
8
7
FB
(Top View)
5
EN
6
COMP
PIN FUNCTION DESCRIPTIONS
Pin No. Symbol Description
1 VIN Input voltage from battery. Place an input filter capacitor in close proximity to this pin.
2 DRV Output voltage to provide a regulated voltage to the Power Switch gate driver.
3 GND Battery return, and output voltage ground reference.
4 EN This TTL compatible Enable input allows the direct connection of Battery as the enable signal. Grounding
this input stops switching and reduces quiescent current draw to a minimum.
5 COMP Error Amplifier output, for tailoring transient response with external compensation components.
6 FB Feedback input pin to program output voltage, and detect pre−charged or shorted output conditions.
7 BST Bootstrap input provides drive voltage higher than VIN to the N−channel Power Switch for optimum
switch R
DS(on)
and highest efficiency.
8 SW Switching node of the Regulator. Connect the output inductor and cathode of the freewheeling diode to
this pin.
Exposed
Pad
Connect to Pin 3 (electrical ground) and to a low thermal resistance path to the ambient temperature
environment.
NCV890130
http://onsemi.com
5
ELECTRICAL CHARACTERISTICS (V
IN
= 4.5 V to 28 V, V
EN
= 5 V, V
BST
= V
SW
+ 3.0 V, C
DRV
= 0.1 mF, Min/Max values are valid
for the temperature range −40°C T
J
150°C unless noted otherwise, and are guaranteed by test, design or statistical correlation.)
Parameter Symbol Conditions Min Typ Max Unit
QUIESCENT CURRENT
Quiescent Current, shutdown
I
qSD
V
IN
= 13.2 V, V
EN
= 0 V, T
J
= 25°C
10
mA
Quiescent Current, enabled I
qEN
V
IN
= 13.2 V
3.0 mA
UNDERVOLTAGE LOCKOUT − VIN (UVLO)
UVLO Start Threshold
V
UVLSTT
V
IN
rising 4.1 4.5 V
UVLO Stop Threshold V
UVLSTP
V
IN
falling 3.9 4.4 V
UVLO Hysteresis V
UVLOHY
0.1 0.2 V
ENABLE (EN)
Logic Low
V
ENLO
0.8 V
Logic High V
ENHI
2.0 V
Input Current I
EN
8.0 30
mA
SOFT−START (SS)
Soft−Start Completion Time
t
SS
0.8 1.4 2.0 ms
VOLTAGE REFERENCE
FB Pin Voltage during regulation V
FBR
COMP shorted to FB 0.786 0.8 0.814 V
ERROR AMPLIFIER
FB Bias Current
I
FBBIAS
V
FB
= 0.8 V 0.25 1.0
mA
Transconductance
g
m
g
m(HV)
V
COMP
= 1.3 V
4.5 V < V
IN
< 18 V
20 V < V
IN
< 28 V
0.6
0.3
1.0
0.5
1.5
0.75
mmho
Output Resistance R
OUT
1.4
MW
COMP Source Current Limit I
SOURCE
V
FB
= 0.63 V, V
COMP
= 1.3 V
4.5 V < V
IN
< 18 V
20 V < V
IN
< 28 V
75
40
mA
COMP Sink Current Limit I
SINK
V
FB
= 0.97 V, V
COMP
= 1.3 V
4.5 V < V
IN
< 18 V
20 V < V
IN
< 28 V
75
40
mA
Minimum COMP voltage V
CMPMIN
V
FB
= 0.97 V 0.2 0.7 V
OSCILLATOR
Frequency
F
SW
F
SW(HV)
4.5 < V
IN
< 18 V
20 V < V
IN
< 28 V
1.8
0.9
2.0
1.0
2.2
1.1
MHz
VIN FREQUENCY FOLDBACK MONITOR
Frequency Foldback Threshold
V
IN
rising
V
IN
falling
V
FLDUP
V
FLDDN
V
FB
= 0.63 V
18.4
18
20
19.8
V
Frequency Foldback Hysteresis V
FLDHY
0.2 0.3 0.4 V
VIN OVERVOLTAGE SHUTDOWN MONITOR
Overvoltage Stop Threshold
V
OVSTP
32.4 36 V
Overvoltage Start Threshold V
OVSTT
30 35.4 V
Overvoltage Hysteresis V
OVHY
0.6 1.5 2.4 V
SLOPE COMPENSATION
Ramp Slope (Note 1)
(With respect to switch current)
S
ramp
S
ramp(HV)
4.5 < V
IN
< 18 V
20 V < V
IN
< 28 V
0.7
0.25
1.3
0.6
A/ms
1. Not tested in production. Limits are guaranteed by design.
NCV890130
http://onsemi.com
6
ELECTRICAL CHARACTERISTICS (V
IN
= 4.5 V to 28 V, V
EN
= 5 V, V
BST
= V
SW
+ 3.0 V, C
DRV
= 0.1 mF, Min/Max values are valid
for the temperature range −40°C T
J
150°C unless noted otherwise, and are guaranteed by test, design or statistical correlation.)
Parameter UnitMaxTypMinConditionsSymbol
POWER SWITCH
ON Resistance
R
DSON
V
BST
= V
SW
+ 3.0 V 650
mW
Leakage current VIN to SW I
LKSW
V
EN
= 0 V, V
SW
= 0, V
IN
= 18 V 10
mA
Minimum ON Time t
ONMIN
Measured at SW pin 45 70 ns
Minimum OFF Time t
OFFMIN
Measured at SW pin
At F
SW
= 2 MHz (normal)
At F
SW
= 500 kHz (max duty cycle) 30
30
50 70
ns
PEAK CURRENT LIMIT
Current Limit Threshold
I
LIM
1.4 1.55 1.7 A
SHORT CIRCUIT FREQUENCY FOLDBACK
Lowest Foldback Frequency
Lowest Foldback Frequency − High V
in
Hiccup Mode
F
SWAF
F
SWAFHV
F
SWHIC
V
FB
= 0 V, 4.5 V < V
IN
< 18 V
V
FB
= 0 V, 20 V < V
IN
< 28 V
V
FB
= 0 V
400
200
24
500
250
32
600
300
40
kHz
GATE VOLTAGE SUPPLY (DRV pin)
Output Voltage
V
DRV
3.1 3.3 3.5 V
DRV POR Start Threshold V
DRVSTT
2.7 2.9 3.05 V
DRV POR Stop Threshold V
DRVSTP
2.5 2.8 3.0 V
DRV Current Limit I
DRVLIM
V
DRV
= 0 V 16 45 mA
OUTPUT PRECHARGE DETECTOR
Threshold Voltage
V
SSEN
20 35 50 mV
THERMAL SHUTDOWN
Activation Temperature (Note 1)
T
SD
150 190 °C
Hysteresis (Note 1) T
HYS
5 20 °C
1. Not tested in production. Limits are guaranteed by design.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.

NCV890130MWTXG

Mfr. #:
Manufacturer:
ON Semiconductor
Description:
Switching Voltage Regulators 1.2A 2MHz Automotive
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet