7
Switching Specifications (T
A
= 25°C)
Parameter Sym. Device Min. Typ. Max. Units Test Conditions Fig. Note
Propagation t
PLH
HCPL-3100 - 1 2 µsI
F
= 10 mA V
CC
= 24 V, 9, 2, 6
Delay Time to V
O1
= 24 V, 25,
High Output HCPL-3101 - 0.3 0.5 µsI
F
= 5 mA R
G
= 47 Ω, 26,
Level C
G
= 3000 pF 27
Propagation t
PHL
HCPL-3100 - 1 2 µsI
F
= 10 mA
Delay Time to
Low Output HCPL-3101 - 0.3 0.5 µsI
F
= 5 mA
Level
Rise Time t
r
HCPL-3100 - 0.2 0.5 µsI
F
= 10 mA
HCPL-3101 I
F
= 5 mA
Fall Time t
f
HCPL-3100 - 0.2 0.5 µsI
F
= 10 mA
HCPL-3101 I
F
= 5 mA
Output High |CM
H
| HCPL-3100 15 - kV/µsI
F
= 10 mA V
CM
= 1500 V 10 2
Level Common (peak),
Mode Transient HCPL-3101 I
F
= 5mA V
CC
= 24 V
Immunity V
O1
= 24 V
∆V
02H
= ∆V
02L
Output Low |CM
L
|15-kV/µsI
F
= 0 mA = 2.0 V
Level Common
Mode Transient
Immunity
Notes:
1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 11 and 12.
2. A bypass capacitor of 0.01 µF or more is needed near the device between V
CC
and GND when measuring output and transfer
characteristics.
3. I
FLH
represents the forward current when the output goes from low to high.
4. Device considered a two terminal device; pins 1-4 are shorted together and pins 5-8 are shorted together.
5. For devices with minimum V
ISO
specified at 5000 V rms, in accordance with UL 1577, each optocoupler is proof-tested by
applying an insulation test voltage ≥ 6000 V rms for one second (leakage current detection limit, I
I-O
≤ 200 µA).
6. The t
PLH
and t
PHL
propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.
7. R
2
limits the Q1 and Q2 peak currents. For more applications and circuit design information see Application Note “Power
Transistor Gate/Base Drive Optocouplers.”
Packaging Characteristics
Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note
Input-Output Momentary V
ISO
5000 V rms RH = 40% to 60% 4, 5
Withstand Voltage* t = 1 min, T
A
= 25°C
Resistance (Input-Output) R
I-O
5x10
10
10
11
– Ω V
I-O
= 500 V, T
A
= 25°C4
RH = 40% to 60%
Capacitance (Input-Output) C
I-O
– 1.2 – pF f = 1 MHz 4
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification, or Avago Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
