3
ECL Pro®
SY100EP196V
Micrel
M0644-012704
Pin Number Pin Name Pin Function
23, 25, 26, 27, 29, D[0:9] CMOS, ECL, or TTL Select Inputs: These digital control signals adjust the amount of
30, 31, 32, 1, 2 delay from IN to Q. Please refer to the “AC Electrical Table” (page 3) and Table 7 (page
17) for delay values. Figure 9 shows how to interface these inputs to various logic family
standards. These inputs default to logic low when left unconnected. Bit 0 is the least
significant bit, and bit 9 is the most significant bit.
3 D[10] CMOS, ECL, or TTL Select Input: This input latches just like D[0:9] does. It drives the
CASCADE, /CASCADE differential pair. Use only when cascading two or more
SY100EP196V to extend the range of delays required.
4, 5 IN, /IN ECL Input: This is the signal to be delayed. If this input pair is left unconnected, this is
equivalent to a logic low input.
6 VBB Voltage Output Reference: When using a single-ended logic source for IN and /IN,
connect the unused input of the differential pair to this pin. This pin can also re-bias AC-
coupled inputs to IN and /IN. When used, de-couple this pin to V
CC
through an 0.01µF
capacitor. Limit current sinking or sourcing to 0.5mA or less.
7 VEF Voltage Output: Connect this pin to VCF when the D inputs are ECL. Refer to the
“Digital
Control Logic Standard”
section of the
“Functional Description”
to interface the D inputs to
CMOS or TTL.
8 VCF Voltage Input: The voltage at this pin sets the logic transition threshold for the D inputs.
9, 24, 28 VEE Most Negative Supply. Supply ground for PECL systems.
10 LEN ECL Control Input: When logic low, the D inputs flow through. Any changes to the D inputs
reflect in the delay between IN, /IN and Q, /Q. When logic high, the logic values at D are
latched, and these latched bits determine the delay.
11 SETMIN ECL Control Input: When logic high, the contents of the D register are reset. This sets the
delay to the minimum possible, equivalent to D[0:9] being set to 0000000000. When logic
low, the value of the D register, or the logic value of SETMAX determines the delay from
IN, /IN to Q, /Q. This input defaults to logic low when left unconnected.
12 SETMAX ECL Control Input: When logic high and SETMIN is logic low, the contents of the D
register are set high, and the delay is set to one step greater than the maximum possible
with D[0:9] set to 1111111111. When logic low, the value of the D register, or the logic
value of SETMIN determines the delay from IN, /IN to Q, /Q. This input defaults to logic
low when left unconnected.
13, 18, 19, 22 VCC Most Positive Supply: Supply ground for NECL systems. Bypass to V
EE
with 0.1µF and
0.01µF low ESR capacitors.
14, 15 CASCADE, 100k ECL Outputs: These outputs are used when cascading two or more SY100EP196V
to /CASCADE extend the delay range required. Refer to Table 7 (page 17) for delay
values.
16 /EN ECL Control Input: When set active low, Q, /Q are a delayed version of IN, /IN. When set
inactive high, IN, /IN are gated such that Q, /Q become a differential logic low. This input
defaults to logic low when left unconnected.
17 FTUNE Voltage Control Input: By varying the voltage at this pin from V
CC
through V
EE
, the delay
may be fine tuned by approximately ±15ps.
20, 21 Q, /Q 100k ECL Outputs: This signal pair is the delayed version of IN, /IN.
PIN DESCRIPTION
