LTC3728L-1
4
3728l1fc
ELECTRICAL CHARACTERISTICS
The l denotes the specifi cations which apply over the full operating
temperature range, otherwise specifi cations are at T
A
= 25°C. V
IN
= 15V, V
RUN/SS1, 2
= 5V unless otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
I
PLLFLTR
Phase Detector Output Current
Sinking Capability
Sourcing Capability
f
PLLIN
< f
OSC
f
PLLIN
> f
OSC
–15
15
µA
µA
3.3V Linear Regulator
V
3.3OUT
3.3V Regulator Output Voltage No Load
●
3.2 3.35 3.45 V
V
3.3IL
3.3V Regulator Load Regulation I
3.3
= 0 to 10mA 0.5 2 %
V
3.3VL
3.3V Regulator Line Regulation 6V < V
IN
< 30V 0.05 0.2 %
I
3.3LEAK
Leakage Current in Shutdown V
RUN/SS1
= 0V; V
RUN/SS2
= 0V, V
IN
= 3V
●
10 50 µA
PGOOD Output
V
PGL
PGOOD Voltage Low I
PGOOD
= 2mA 0.1 0.3 V
I
PGOOD
PGOOD Leakage Current V
PGOOD
= 5V ±1 µA
V
PG
PGOOD Trip Level, Either Controller V
OSENSE
with Respect to Set Output Voltage
V
OSENSE
Ramping Negative
V
OSENSE
Ramping Positive
–6
6
–7.5
7.5
–9.5
9.5
%
%
Effi ciency vs Output Current
and Mode (Figure 13)
Effi ciency vs Output Current
(Figure 13)
Effi ciency vs Input Voltage
(Figure 13)
TYPICAL PERFORMANCCE CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: T
J
is calculated from the ambient temperature T
A
and power
dissipation P
D
according to the following formulas:
LTC3728LUH-1: T
J
= T
A
+ (P
D
• 34°C/W)
LTC3728LGN-1: T
J
= T
A
+ (P
D
• 95°C/W)
Note 3: The IC is tested in a feedback loop that servos V
ITH1, 2
to a
specifi ed voltage and measures the resultant V
OSENSE1, 2.
Note 4: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications Information.
Note 5: Rise and fall times are measured using 10% and 90% levels. Delay
times are measured using 50% levels.
Note 6: The minimum on-time condition is specifi ed for an inductor
peak-to-peak ripple current ≥40% of I
MAX
(see minimum on-time
considerations in the Applications Information section).
Note 7: The LTC3728LE-1 are guaranteed to meet performance
specifi cations from 0°C to 85°C. Specifi cations over the –40°C to 85°C
operating temperature range are assured by design, characterization
and correlation with statistical process controls. The LTC3728LI-1 is
guaranteed to meet performance specifi cations over the full –40°C to 85°C
operating temperature range
OUTPUT CURRENT (A)
0.001
0
EFFICIENCY (%)
10
30
40
50
100
70
0.01
0.1
1
3728L1 G01
20
80
90
60
10
FORCED
CONTINUOUS
MODE (PWM)
CONSTANT
FREQUENCY
(BURST DISABLE)
Burst Mode
OPERATION
V
IN
= 15V
V
OUT
= 5V
f = 250kHz
OUTPUT CURRENT (A)
0.001
EFFICIENCY (%)
70
80
10
3728L1 G02
60
50
0.01
0.1
1
100
90
V
IN
= 10V
V
IN
= 15V
V
IN
= 7V
V
IN
= 20V
V
OUT
= 5V
f = 250kHz
INPUT VOLTAGE (V)
5
EFFICIENCY (%)
70
80
3728L1 G03
60
50
15
25
35
100
V
OUT
= 5V
I
OUT
= 3A
f = 250kHz
90
