OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

2320555

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21
QUINT-PS/24DC/24DC/10/CO
105538_en_01 PHOENIX CONTACT 10
9 Dimensions and mounting positions
Figure 4 Dimensions
Possible mounting positions:
Normal mounting position, installation depth 125 mm (+ DIN rail) (delivery state)
Rotated mounting position, 270° Y-axis, installation depth: 51 mm (+ DIN rail)
5
5
48
130
122
50
115
230
Output DC 24V 10A
Boost
DC OK
18-29.5 V
U <19.2 V
IN
Input DC 24V
QUINT POWER
13
14
19.2V
>
IN
U
!
QUINT-PS/24DC/24DC/10/CO
105538_en_01 PHOENIX CONTACT 11
10 Mounting on DIN rails
10.1 Normal mounting position
Assembly:
Position the DC/DC converter with the DIN rail guide on the
top edge of the DIN rail and snap it in by pushing downward.
Removing:
Pull back the snap-on catch using a screwdriver and detach
the DC/DC converter from the bottom edge of the DIN rail.
10.2 Rotated mounting position (270° Y-axis)
A rotated mounting position can be achieved for the DC/DC
converter by mounting the device on the DIN rail at a 270°
angle. Mount the DIN rail adapter (UTA 107/30) as shown in
the figure. No additional mounting material is required.
Mounting screws: Torx® T10 (0.8 Nm ... 0.9 Nm tightening
torque).
Figure 5 Rotated mounting position (270° Y-axis)
11 Input
Connection to the input voltage is established via the screw
connectors on the DC input screw connection.
The DC/DC converter converts a DC voltage of 18...32V
into adjustable, regulated, and electrically isolated output
voltage.
The DC/DC converter requires an input voltage of 18V. Dur-
ing operation, this can drop down to 14V, then observe the
voltage-dependent derating.
Figure 6 Input
11.1 Protection of the primary side
Installation of the DC/DC converter must correspond to EN
60950 regulations.
An internal fuse is provided for device protection. Additional
device protection is not required.
The connecting cables on the primary side should have
large cross sections to keep the voltage drops in the cables
as low as possible.
Other mounting positions are also possible.
Always observe position-dependent derating.
NOTE: Device may be damaged
If an internal fuse trips, this is due to a device
fault. In this case, the DC/DC converter must
be inspected in the factory.
13
14
_
_
_
OK
DC
I
<
I
N
OK
O
I
N
O
utput D
C 24
V
10A
Boost
DC OK
U <19.2 V
IN
Inp
ut D
C
24
V
QUINT POWER
13
14
19.2V
>
I
N
U
18-29.5V
!
QUINT-PS/24DC/24DC/10/CO
105538_en_01 PHOENIX CONTACT 12
12 Output
Connection of the output voltage is established via the
screw connectors on the DC output screw connection.
The output voltage can be set on the potentiometer.
Figure 7 Output
12.1 Protecting the secondary side
The DC/DC converter is electronically short-circuit-proof
and idling-proof. In the event of an error, the output voltage
is limited. It must be ensured that all output cables are di-
mensioned accordingly for the maximum output current or
have separate protection.
The connecting cables on the secondary side should have
large cross sections to keep the voltage drops in the cables
as low as possible.
13 Output characteristic curve
The DC/DC converter works with the POWER BOOST
power reserve as shown in the U/I characteristic curve in the
figure. At ambient temperatures < 40°C, I
BOOST
is perma-
nently available. It is also available at higher temperatures
for a few minutes.
In the event of a secondary-side short circuit or overload, the
output current is limited to I
BOOST
. In this case, the DC/DC
converter does not switch off but supplies output current
continuously. The secondary voltage is then reduced until
the short circuit is eliminated. The U/I characteristic curve
with the POWER BOOST power reserve ensures that high
inrush currents of capacitive loads in the primary circuit can
be supplied reliably.
Figure 8 Output characteristic curve
–U
N
= 24 V
–I
N
= 10 A
–I
BOOST
= 12.5 A
– SFB Technology = 60 A (for 12 ms)
–P
N
= 240 W
–P
BOOST
= 300 W
13
14
_
_
_
O
K
D
C
I
<
I
N
O
K
O
IN
O
u
tp
u
t D
C
2
4
V
1
0
A
Boost
D
C O
K
U <19
.2 V
IN
In
p
u
t D
C
2
4
V
QUINT POWER
1
3
1
4
19
.2V
>
IN
U
18-29.5V
!
I [A]
OUT
U [V]
OUT
U
N
I
N
I<I
N
<60 °C
U <0,9 x U
N
I>I
N
<40°C
I
BOOST
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21

2320555

Mfr. #:
Buy 2320555
Manufacturer:
Phoenix Contact
Description:
DIN Rail Power Supplies QUINT-PS/24DC 24DC/10/CO
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet