OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

X28HC256PIZ-90

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P19
X28HC256
16
FN8108.5
August 27, 2015
Submit Document Feedback
Small Outline Plastic Packages (SOIC)
M28.3 (JEDEC MS-013-AE ISSUE C)
28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A 0.0926 0.1043 2.35 2.65 -
A1 0.0040 0.0118 0.10 0.30 -
B 0.013 0.0200 0.33 0.51 9
C 0.0091 0.0125 0.23 0.32 -
D 0.6969 0.7125 17.70 18.10 3
E 0.2914 0.2992 7.40 7.60 4
e 0.05 BSC 1.27 BSC -
H 0.394 0.419 10.00 10.65 -
h 0.01 0.029 0.25 0.75 5
L 0.016 0.050 0.40 1.27 6
N28 287
0
o
8
o
0
o
8
o
-
Rev. 1, 1/13
NOTES:
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above
the seating plane, shall not exceed a maximum value of 0.61mm
(0.024 inch)
10. Controlling dimension: MILLIMETER. Converted inch dimensions are
not necessarily exact.
X28HC256
17
FN8108.5
August 27, 2015
Submit Document Feedback
Plastic Leaded Chip Carrier Packages (PLCC)
N32.45x55 (JEDEC MS-016AE ISSUE A)
32 LEAD PLASTIC LEADED CHIP CARRIER PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A 0.125 0.140 3.18 3.55 -
A1 0.060 0.095 1.53 2.41 -
D 0.485 0.495 12.32 12.57 -
D1 0.447 0.453 11.36 11.50 3
D2 0.188 0.223 4.78 5.66 4, 5
E 0.585 0.595 14.86 15.11 -
E1 0.547 0.553 13.90 14.04 3
E2 0.238 0.273 6.05 6.93 4, 5
N28 286
ND 7 7 7
NE 9 9 7
Rev. 0 7/98
NOTES:
1. Controlling dimension: INCH. Converted millimeter dimen-
sions are not necessarily exact.
2. Dimensions and tolerancing per ANSI Y14.5M-1982.
3. Dimensions D1 and E1 do not include mold protrusions. Al-
lowable mold protrusion is 0.010 inch (0.25mm) per side.
Dimensions D1 and E1 include mold mismatch and are mea-
sured at the extreme material condition at the body parting
line.
4. To be measured at seating plane contact point.
5. Centerline to be determined where center leads exit plastic
body.
6. “N” is the number of terminal positions.
7. ND denotes the number of leads on the two shorts sides of the
package, one of which contains pin #1. NE denotes the num-
ber of leads on the two long sides of the package.
-C-
X28HC256
18
FN8108.5
August 27, 2015
Submit Document Feedback
Small Outline Package Family (SO)
GAUGE
PLANE
A2
A1
L
L1
DETAIL X
4° ±4°
SEATING
PLANE
e
H
b
C
0.010 BM CA
0.004 C
0.010 BM CA
B
D
(N/2)
1
E1
E
NN
(N/2)+1
A
PIN #1
I.D. MARK
h X 45°
A
SEE DETAIL “X”
c
0.010
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
SYMBOL
INCHES
TOLERANCE NOTESSO-8 SO-14
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX -
A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 0.003 -
A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 0.002 -
b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 0.003 -
c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 0.001 -
D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 0.004 1, 3
E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 0.008 -
E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 0.004 2, 3
e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic -
L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 0.009 -
L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic -
h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference -
N 8 14 16 16 20 24 28 Reference -
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P19

X28HC256PIZ-90

Mfr. #:
Buy X28HC256PIZ-90
Manufacturer:
Renesas / Intersil
Description:
EEPROM 32K X 8 EEPROM,CMOS,HIGH SPEED,PDIP,I.TEMP,90NS,PB FREE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet