R8C/2H Group, R8C/2J Group 5. Electrical Characteristics
Rev.1.00 Mar 28, 2008 Page 45 of 65
REJ03B0217-0100
Table 5.25 Electrical Characteristics (6) [Vcc = 2.2 V]
(T
opr = −20 to 85°C (N version) / −40 to 85°C (D version), unless otherwise specified.)
Symbol Parameter Condition
Standard
Unit
Min. Typ. Max.
I
CC Power supply current
(V
CC = 2.2 to 2.7 V)
Single-chip mode,
output pins are open,
other pins are V
SS
High-speed
on-chip oscillator mode
High-speed on-chip oscillator on = 4 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
− 3.5 − mA
High-speed on-chip oscillator on = 4 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
− 1.5 − mA
Low-speed
on-chip oscillator mode
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8, FMR47 = 1
− 100 230 µA
Low-speed clock mode
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
XCIN clock oscillator on = 32 kHz (low drive)
FMR47 = 1
− 100 230 µA
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
XCIN clock oscillator on = 32 kHz (low drive)
Program operation on RAM
Flash memory off, FMSTP = 1
− 25 −µA
Wait mode
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock operation
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
− 22 60 µA
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
− 20 55 µA
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
XCIN clock oscillator on = 32 kHz (high drive)
While a WAIT instruction is executed
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
BGR trimming circuit disabled (BGRCR0 = 1)
− 3 −µA
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
XCIN clock oscillator on = 32 kHz (low drive)
While a WAIT instruction is executed
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
BGR trimming circuit disabled (BGRCR0 = 1)
− 1.8 −µA
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
XCIN clock oscillator on = 32 kHz (high drive)
While a WAIT instruction is executed
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
BGR trimming circuit enabled (BGRCR0 = 0)
− 7 −µA
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
XCIN clock oscillator on = 32 kHz (low drive)
While a WAIT instruction is executed
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
BGR trimming circuit enabled (BGRCR0 = 0)
− 6 −µA
Stop mode
XCIN clock off, Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit disabled (BGRCR0 = 1)
− 0.7 3 µA
XCIN clock off, Topr = 85°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit disabled (BGRCR0 = 1)
− 1.1 −µA
XCIN clock off, Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit enabled (BGRCR0 = 0)
− 57µA
XCIN clock off, Topr = 85°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit enabled (BGRCR0 = 0)
− 5.5 −µA
