R8C/2H Group, R8C/2J Group 5. Electrical Characteristics
Rev.1.00 Mar 28, 2008 Page 62 of 65
REJ03B0217-0100
Table 5.52 Electrical Characteristics (6) [Vcc = 2.2 V]
(T
opr = 20 to 85°C (N version) / 40 to 85°C (D version), unless otherwise specified.)
Symbol Parameter Condition
Standard
Unit
Min. Typ. Max.
I
CC Power supply current
(V
CC = 2.2 to 2.7 V)
Single-chip mode,
output pins are open,
other pins are V
SS
High-speed
on-chip oscillator
mode
High-speed on-chip oscillator on = 4 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
3.5 mA
High-speed on-chip oscillator on = 4 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
1.5 mA
Low-speed
on-chip oscillator
mode
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8, FMR47 = 1
100 230 µA
Wait mode High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock operation
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
22 60 µA
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
20 55 µA
Stop mode Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit disabled (BGRCR0 = 1)
0.7 3 µA
Topr = 85°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit disabled (BGRCR0 = 1)
1.1 −µA
Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit enabled (BGRCR0 = 0)
57µA
Topr = 85°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
BGR trimming circuit enabled (BGRCR0 = 0)
5.5 −µA
R8C/2H Group, R8C/2J Group 5. Electrical Characteristics
Rev.1.00 Mar 28, 2008 Page 63 of 65
REJ03B0217-0100
Timing requirements
(Unless Otherwise Specified: V
CC = 2.2 V, VSS = 0 V at Topr = 25°C) [VCC = 2.2 V]
Figure 5.23 TRAIO Input Timing Diagram when V
CC = 2.2 V
Table 5.53 TRAIO Input
Symbol Parameter
Standard
Unit
Min. Max.
t
c(TRAIO) TRAIO input cycle time 500 ns
t
WH(TRAIO) TRAIO input “H” width 200 ns
t
WL(TRAIO) TRAIO input “L” width 200 ns
TRAIO input
tC(TRAIO)
tWL(TRAIO)
tWH(TRAIO)
VCC = 2.2 V
R8C/2H Group, R8C/2J Group 5. Electrical Characteristics
Rev.1.00 Mar 28, 2008 Page 64 of 65
REJ03B0217-0100
Figure 5.24 Serial Interface Timing Diagram when VCC = 2.2 V
NOTES:
1. When selecting the digital filter by the INTi
input filter select bit, use an INTi input HIGH width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
2. When selecting the digital filter by the INTi
input filter select bit, use an INTi input LOW width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
Figure 5.25 External Interrupt INTi Input Timing Diagram when VCC = 2.2 V
Table 5.54 Serial Interface
Symbol Parameter
Standard
Unit
Min. Max.
t
c(CK) CLK0 input cycle time 800 ns
t
W(CKH) CLK0 input “H” width 400 ns
t
W(CKL) CLK0 input “L” width 400 ns
t
d(C-Q) TXD0 output delay time 200 ns
t
h(C-Q) TXD0 hold time 0 ns
t
su(D-C) RXD0 input setup time 150 ns
t
h(C-D) RXD0 input hold time 90 ns
Table 5.55 External Interrupt INTi (i = 0 or 1) Input
Symbol Parameter
Standard
Unit
Min. Max.
t
W(INH)
INTi input “H” width
1000
(1)
ns
t
W(INL)
INTi input “L” width
1000
(2)
ns
tW(CKH)
tC(CK)
tW(CKL)
th(C-Q)
th(C-D)
tsu(D-C)td(C-Q)
CLK0
TXD0
RXD0
VCC = 2.2 V
INTi input
tW(INL)
tW(INH)
VCC = 2.2 V
i = 0 or 1

R5F212J0SDSP#U0

Mfr. #:
Manufacturer:
Renesas Electronics
Description:
16-bit Microcontrollers - MCU MCU 2/5V 2K I-Temp Pb-free 20-SSOP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union