2010-2015 Microchip Technology Inc. DS30009622M-page 53
PIC18F2XXX/4XXX FAMILY
6.0 AC/DC CHARACTERISTICS TIMING REQUIREMENTS
FOR PROGRAM/VERIFY TEST MODE
Standard Operating Conditions
Operating Temperature: 25C is recommended
Param
No.
Sym Characteristic Min Max Units Conditions
D110 V
IHH High-Voltage Programming Voltage on
MCLR
/VPP/RE3
V
DD + 4.0 12.5 V (Note 2)
D110A V
IHL Low-Voltage Programming Voltage on
MCLR
/VPP/RE3
2.00 5.50 V (Note 2)
D111 V
DD Supply Voltage During Programming 2.00 5.50 V Externally timed,
Row Erases and all writes
3.0 5.50 V Self-timed,
Bulk Erases only (Note 3)
D112 I
PP Programming Current on MCLR/VPP/RE3 — 300 A (Note 2)
D113 I
DDP Supply Current During Programming — 10 mA
D031 VIL Input Low Voltage VSS 0.2 VDD V
D041 V
IH Input High Voltage 0.8 VDD VDD V
D080 VOL Output Low Voltage — 0.6 V IOL = 8.5 mA @ 4.5V
D090 V
OH Output High Voltage VDD – 0.7 — V IOH = -3.0 mA @ 4.5V
D012 CIO Capacitive Loading on I/O pin (PGD) — 50 pF To meet AC specifications
P1 T
R MCLR/VPP/RE3 Rise Time to Enter
Program/Verify mode
—1.0s (Notes 1, 2)
P2 T
PGC Serial Clock (PGC) Period 100 — ns VDD = 5.0V
1—sVDD = 2.0V
P2A T
PGCL Serial Clock (PGC) Low Time 40 — ns VDD = 5.0V
400 — ns VDD = 2.0V
P2B T
PGCH Serial Clock (PGC) High Time 40 — ns VDD = 5.0V
400 — ns VDD = 2.0V
P3 T
SET1 Input Data Setup Time to Serial Clock 15 — ns
P4 THLD1 Input Data Hold Time from PGC 15 — ns
P5 T
DLY1 Delay Between 4-Bit Command and Command
Operand
40 — ns
P5A T
DLY1A Delay Between 4-Bit Command Operand and
Next 4-Bit Command
40 — ns
P6 T
DLY2 Delay Between Last PGC of Command Byte to
First PGC of Read of Data Word
20 — ns
P9 T
DLY5 PGC High Time (minimum programming time) 1 — ms Externally timed
P10 TDLY6 PGC Low Time After Programming
(high-voltage discharge time)
100 — s
P11 T
DLY7 Delay to Allow Self-Timed Data Write or
Bulk Erase to Occur
5—ms
Note 1: Do not allow excess time when transitioning MCLR
between VIL and VIHH. This can cause spurious program
executions to occur. The maximum transition time is:
1 T
CY + TPWRT (if enabled) + 1024 TOSC (for LP, HS, HS/PLL and XT modes only) +
2 ms (for HS/PLL mode only) + 1.5 s (for EC mode only)
where TCY is the instruction cycle time, TPWRT is the Power-up Timer period and TOSC is the oscillator period. For
specific values, refer to the Electrical Characteristics section of the device data sheet for the particular device.
2: When ICPRT = 1, this specification also applies to ICV
PP.
3: At 0°C-50°C.