Receiver data buffer underflow
Noise error
Framing error
Parity error
Active edge on receive pin
LIN break detect
Receiver framing error detection
Hardware parity generation and checking
1/16 bit-time noise detection
5 channel DMA requests
4.4.8.5 Inter-Integrated Circuit (I2C)
Compatible with I
2
C bus standard and SMBus Specification Version 2 features
Up to 100 kbps with maximum bus loading
Multimaster operation
Software programmable for one of 64 different serial clock frequencies
Programmable slave address and glitch input filter
Interrupt driven byte-by-byte data transfer or DMA support
Arbitration lost interrupt with automatic mode switching from master to slave
Calling address identification interrupt
Bus busy detection broadcast and 10-bit address extension
Address matching causes wakeup when processor is in low power modes
4.4.8.6 Serial Peripheral Interface (SPI)
Master and slave mode
Full-duplex, three-wire synchronous transfers
Programmable transmit bit rate
Double-buffered transmit and receive data registers
Serial clock phase and polarity options
Slave select output
Mode fault error flag with CPU interrupt capability
Control of SPI operation during wait mode
Selectable MSB-first or LSB-first shifting
Programmable 8-bit or 16-bit data transmission length
Receive data buffer hardware match feature
64-bit FIFO mode for high speed transfers of large amounts of data (SPI0 only)
Support for both transmit and receive by DMA
Human-Machine Interface (HMI)
4.4.9.1 Touch Sensing Input (TSI)
Support for as many as 16 input capacitive touch sensing pins with individual result registers
Automatic detection of Electrode Capacitance Change with programmable upper and lower threshold
Automatic periodic scan unit with different duty cycles for run and low power modes
Full support (with Freescale's touch sensing software library suite) for implementing keypads, rotaries, and sliders
Operation across all low power modes: wait, stop, VLPR, VLPW, VLPS, LLS, VLLSx
Capability to wake MCU from low power modes
4.4.9
Human-Machine Interface (HMI)
ColdFire+ Portfolio Product Brief, Rev. 4, 03/2013
22 Freescale Semiconductor, Inc.
Configurable interrupts:
End-of-Scan or Out-of-Range interrupt
TSI Error Interrupts: pad short to Vdd/Vss or Conversion Overrun
Standalone operation not requiring any external crystal even in low power modes
Configurable integration of each electrode capacitance measurement from 1 to 32 times
Programmable Electrode Oscillator and TSI Reference Oscillator for high sensitivity, small scan time, and low power
functionality
Only one pin per electrode implementation with no external hardware required
4.4.9.2 Enhanced General Purpose Input/Output (EGPIO)
Programmable glitch filter on up to 16 input pins and interrupt with selectable polarity on all input pins
Hysteresis and configurable pullup/pulldown device on all input pins
Configurable slew rate and drive strength on all output pins
Independent pin value register to read logic level on digital pin
4.4.9.3 Rapid General Purpose Input/Output (RGPIO)
Package pin toggle rates typically faster than comparable pins mapped onto peripheral bus
16 bits of high-speed GPIO functionality in memory-mapped device connected to the ColdFire core's local 32-bit bus
All reads and writes complete in a single data phase cycle for zero wait-state response
Data bits can be accessed directly or via alternate addresses to provide set, clear, and toggle functions
Unique data direction and pin enable control registers
5 Developer Environment
Freescale's ColdFire products are supported by a widespread, established network of tools and third party developers and
software vendors. The ColdFire+ MCU families take advantage of these and similar development resources.
5.1 Freescale's Tower System Support
Freescale's Tower System is a modular development platform for 8-bit, 16-bit, and 32-bit microcontrollers that enables
advanced development through rapid prototyping. Featuring multiple development boards or modules, the Tower System
provides designers with building blocks for entry-level to advanced microcontroller development.
Developer Environment
ColdFire+ Portfolio Product Brief, Rev. 4, 03/2013
Freescale Semiconductor, Inc. 23
The Freescale Tower System
MCU/MPU Module
• Tower controller board
• Works stand-alone or
in Tower System
• Features new on-board
debug interface for
easy programming
and debugging via
mini-B USB cable
Secondary Elevator
• Additional serial and
expansion buses and
peripheral interfaces
Peripheral Module
(i.e. serial, prototype, etc.)
Size
Tower is approx. 3.5” H x 3.5” W x 3.5” D
when fully assembled
Primary Elevator
Common serial
and expansion
bus signals
Two 2x80 connectors
on backside for easy
signal access and
side-mounting board
(i.e. LCD module)
Power regulation
circuitry
Standardized signal
assignments
Board Connectors
Four card-edge
connectors
Uses PCI Express
®
connectors
(x16, 90 mm/3.5”
long, 164 pins)
Figure 3. Freescale's Tower System
Table 8. Tower Modules for ColdFire+ MCU Families
Microcontroller Modules Features
ColdFire+ JF Family MCU Module
TWR-MCF51JF
TWR-MCF51JF-KIT (contains TWR-ELEV and
TWR-PROTO)
JF family 128 KB flash MCU in 64 LQFP package
On-board BDM debug interface
Access to all features
ColdFire+ QM Family MCU Module
TWR-MCF51QM
TWR-MCF51QM-KIT (contains TWR-ELEV and
TWR-PROTO)
QM family 128 KB flash MCU in 64 LQFP package
On-board BDM debug interface
Access to all features
Developer Environment
ColdFire+ Portfolio Product Brief, Rev. 4, 03/2013
24 Freescale Semiconductor, Inc.

LPC54113J256UK49Z

Mfr. #:
Manufacturer:
NXP Semiconductors
Description:
ARM Microcontrollers - MCU LPC54113J256UK49/UNCASED///REEL 7 Q1 DP CHIPS
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet