OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

NX3L1T53GM,125

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24
NX3L1T53 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved.
Product data sheet Rev. 8 — 23 January 2013 4 of 24
NXP Semiconductors
NX3L1T53
Low-ohmic single-pole double-throw analog switch
7.2 Pin description
8. Functional description
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care.
Fig 5. Pin configuration SOT902-2 (XQFN8)
001aaj538
EY1
Z
V
CC
GND
Y0
GND
S
Transparent top view
3
6
4
1
5
8
7
2
terminal 1
index area
NX3L1T53
Table 3. Pin description
Symbol Pin Description
SOT833-1 and SOT996-2 SOT902-2
Z 1 7 common output or input
E
2 6 enable input (active LOW)
GND 3 5 ground (0 V)
GND 4 4 ground (0 V)
S 5 3 select input
Y1 6 2 independent input or output
Y0 7 1 independent input or output
V
CC
8 8 supply voltage
Table 4. Function table
[1]
Input Channel on
S E
L L Y0 to Z or Z to Y0
H L Y1 to Z or Z to Y1
X H switch off
NX3L1T53 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved.
Product data sheet Rev. 8 — 23 January 2013 5 of 24
NXP Semiconductors
NX3L1T53
Low-ohmic single-pole double-throw analog switch
9. Limiting values
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For XSON8 and XQFN8 packages: above 118 C the value of P
tot
derates linearly with 7.8 mW/K.
10. Recommended operating conditions
[1] To avoid sinking GND current from terminal Z when switch current flows in terminal Yn, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current will flow from terminal Yn. In this case, there is no limit
for the voltage drop across the switch.
[2] Applies to control signal levels.
Table 5. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
V
CC
supply voltage 0.5 +4.6 V
V
I
input voltage select input S and enable input E
[1]
0.5 +4.6 V
V
SW
switch voltage
[2]
0.5 V
CC
+ 0.5 V
I
IK
input clamping current V
I
< 0.5 V 50 - mA
I
SK
switch clamping current V
I
< 0.5 V or V
I
>V
CC
+ 0.5 V - 50 mA
I
SW
switch current V
SW
> 0.5 V or V
SW
< V
CC
+ 0.5 V;
source or sink current
- 350 mA
V
SW
> 0.5 V or V
SW
< V
CC
+ 0.5 V;
pulsed at 1 ms duration, < 10 % duty cycle;
peak current
- 500 mA
T
stg
storage temperature 65 +150 C
P
tot
total power dissipation T
amb
= 40 Cto+125C
[3]
- 250 mW
Table 6. Recommended operating conditions
Symbol Parameter Conditions Min Typ Max Unit
V
CC
supply voltage 1.4 - 4.3 V
V
I
input voltage select input S and enable
input E
0- 4.3V
V
SW
switch voltage
[1]
0- V
CC
V
T
amb
ambient temperature 40 - +125 C
t/V input transition rise and fall rate V
CC
= 1.4 V to 4.3 V
[2]
- - 200 ns/V
NX3L1T53 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved.
Product data sheet Rev. 8 — 23 January 2013 6 of 24
NXP Semiconductors
NX3L1T53
Low-ohmic single-pole double-throw analog switch
11. Static characteristics
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter Conditions T
amb
= 25 C T
amb
= 40 C to +125 C Unit
Min Typ Max Min Max
(85 C)
Max
(125 C)
V
IH
HIGH-level
input voltage
V
CC
= 1.4 V to 1.6 V 0.9 - - 0.9 - - V
V
CC
= 1.65 V to 1.95 V 0.9 - - 0.9 - - V
V
CC
= 2.3 V to 2.7 V 1.1 - - 1.1 - - V
V
CC
= 2.7 V to 3.6 V 1.3 - - 1.3 - - V
V
CC
= 3.6 V to 4.3 V 1.4 - - 1.4 - - V
V
IL
LOW-level
input voltage
V
CC
= 1.4 V to 1.6 V - - 0.3 - 0.3 0.3 V
V
CC
= 1.65 V to 1.95 V - - 0.4 - 0.4 0.3 V
V
CC
= 2.3 V to 2.7 V - - 0.4 - 0.4 0.4 V
V
CC
= 2.7 V to 3.6 V - - 0.5 - 0.5 0.5 V
V
CC
= 3.6 V to 4.3 V - - 0.6 - 0.6 0.6 V
I
I
input leakage
current
select input S and enable
input E; V
I
= GND to 4.3 V;
V
CC
= 1.4 V to 4.3 V
--- -0.5 1 A
I
S(OFF)
OFF-state
leakage
current
Y0 and Y1 port;
see Figure 6
V
CC
= 1.4 V to 3.6 V - - 5-50 500 nA
V
CC
= 3.6 V to 4.3 V - - 10 - 50 500 nA
I
S(ON)
ON-state
leakage
current
Z port; see Figure 7
V
CC
= 1.4 V to 3.6 V - - 5-50 500 nA
V
CC
= 3.6 V to 4.3 V - - 10 - 50 500 nA
I
CC
supply current V
I
=V
CC
or GND;
V
SW
=GNDorV
CC
V
CC
= 3.6 V - - 100 - 690 6000 nA
V
CC
= 4.3 V - - 150 - 800 7000 nA
I
CC
additional
supply current
V
SW
=GNDorV
CC
V
I
= 2.6 V; V
CC
=4.3V - 2.0 4.0 - 7 7 A
V
I
= 2.6 V; V
CC
= 3.6 V - 0.35 0.7 - 1 1 A
V
I
= 1.8 V; V
CC
= 4.3 V - 7.0 10.0 - 15 15 A
V
I
= 1.8 V; V
CC
=3.6V - 2.5 4.0 - 5 5 A
V
I
= 1.8 V; V
CC
= 2.5 V - 50 200 - 300 500 nA
C
I
input
capacitance
-1.0----pF
C
S(OFF)
OFF-state
capacitance
-35----pF
C
S(ON)
ON-state
capacitance
-130----pF
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24

NX3L1T53GM,125

Mfr. #:
Buy NX3L1T53GM,125
Manufacturer:
NXP Semiconductors
Description:
Analog Switch ICs 1SW SPDT 4.3V 60MHz
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet