Philips Semiconductors Product data
XA-G30
XA 16-bit microcontroller family
512 B RAM, watchdog, 2 UARTs
2002 Mar 25
7
NAME
RESET
VALUE
BIT FUNCTIONS AND ADDRESSES
SFR
ADDRESS
DESCRIPTION
NAME
RESET
VALUE
LSBMSB
SFR
ADDRESS
DESCRIPTION
357 356 355 354 353 352 351 350
SWR* Software Interrupt Request 42A — SWR7 SWR6 SWR5 SWR4 SWR3 SWR2 SWR1 00
2C7 2C6 2C5 2C4 2C3 2C2 2C1 2C0
T2CON* Timer 2 control register 418 TF2 EXF2 RCLK0 TCLK0
EXEN2
TR2 C/T2
CP/RL2
00
2CF 2CE 2CD 2CC 2CB 2CA 2C9 2C8
T2MOD* Timer 2 mode control 419 — — RCLK1 TCLK1 — — T2OE DCEN 00
TH2 Timer 2 high byte 459 00
TL2 Timer 2 low byte 458 00
T2CAPH Timer 2 capture register,
high byte
45B 00
T2CAPL Timer 2 capture register,
low byte
45A 00
287 286 285 284 283 282 281 280
TCON* Timer 0 and 1 control register 410 TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00
TH0 Timer 0 high byte 451 00
TH1 Timer 1 high byte 453 00
TL0 Timer 0 low byte 450 00
TL1 Timer 1 low byte 452 00
TMOD Timer 0 and 1 mode control 45C GATE C/T M1 M0 GATE C/T M1 M0 00
28F 28E 28D 28C 28B 28A 289 288
TSTAT* Timer 0 and 1 extended status 411 — — — — — T1OE — T0OE 00
2FF 2FE 2FD 2FC 2FB 2FA 2F9 2F8
WDCON*
Watchdog control register 41F PRE2 PRE1 PRE0 — —
WDRUN WDTOF
—
Note 6
WDL Watchdog timer reload 45F 00
WFEED1
Watchdog feed 1 45D x
WFEED2
Watchdog feed 2 45E x
NOTES:
* SFRs are bit addressable.
1. At reset, the BCR register is loaded with the binary value 0000 0a11, where “a” is the value on the BUSW pin. This defaults the address bus
size to 20 bits since the XA-G30 has only 20 address lines.
2. SFR is loaded from the reset vector.
3. All bits except F1, F0, and P are loaded from the reset vector. Those bits are all 0.
4. Unimplemented bits in SFRs are X (unknown) at all times. Ones should not be written to these bits since they may be used for other
purposes in future XA derivatives. The reset value shown for these bits is 0.
5. Port configurations default to quasi-bidirectional when the XA begins execution from internal code memory after reset, based on the
condition found on the EA pin. Thus all PnCFGA registers will contain FF and PnCFGB registers will contain 00. When the XA begins
execution using external code memory, the default configuration for pins that are associated with the external bus will be push-pull. The
PnCFGA and PnCFGB register contents will reflect this difference.
6. The WDCON reset value is E6 for a Watchdog reset, E4 for all other reset causes.
7. The XA-G30 implements an 8-bit SFR bus, as stated in Chapter 8 of the
XA User Guide
. All SFR accesses must be 8-bit operations. Attempts
to write 16 bits to an SFR will actually write only the lower 8 bits. Sixteen bit SFR reads will return undefined data in the upper byte.
