LPC2212_2214 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved.
Product data sheet Rev. 5 — 14 June 2011 6 of 47
NXP Semiconductors
LPC2212/2214
Single-chip 16/32-bit ARM microcontrollers
5.2 Pin description
Table 3. Pin description
Symbol Pin Type Description
P0[0] to P0[31] I/O Port 0 is a 32-bit bidirectional I/O port with individual direction controls for
each bit. The operation of port 0 pins depends upon the pin function selected
via the Pin Connect Block.
Pins 26 and 31 of port 0 are not available.
P0[0]/TXD0/PWM1 42 O TXD0 — Transmitter output for UART0.
O PWM1 — Pulse Width Modulator output 1.
P0[1]/RXD0/PWM3/
EINT0
49 I RXD0 — Receiver input for UART0.
O PWM3 — Pulse Width Modulator output 3.
I EINT0 — External interrupt 0 input
P0[2]/SCL/CAP0[0] 50 I/O SCL — I
2
C-bus clock input/output. Open-drain output (for I
2
C-bus
compliance).
I CAP0[0] — Capture input for Timer 0, channel 0.
P0[3]/SDA/MAT0[0]/
EINT1
58 I/O SDA — I
2
C-bus data input/output. Open-drain output (for I
2
C-bus
compliance).
O MAT0[0] — Match output for Timer 0, channel 0.
I EINT1 — External interrupt 1 input.
P0[4]/SCK0/CAP0[1] 59 I/O SCK0 — Serial clock for SPI0. SPI clock output from master or input to slave.
I CAP0[1] — Capture input for Timer 0, channel 1.
P0[5]/MISO0/MAT0[1] 61 I/O MISO0 — Master In Slave OUT for SPI0. Data input to SPI master or data
output from SPI slave.
O MAT0[1] — Match output for Timer 0, channel 1.
P0[6]/MOSI0/CAP0[2] 68 I/O MOSI0 — Master Out Slave In for SPI0. Data output from SPI master or data
input to SPI slave.
I CAP0[2] — Capture input for Timer 0, channel 2.
P0[7]/SSEL0/PWM2/
EINT2
69 I SSEL0 — Slave Select for SPI0. Selects the SPI interface as a slave.
O PWM2 — Pulse Width Modulator output 2.
I EINT2 — External interrupt 2 input.
P0[8]/TXD1/PWM4 75 O TXD1 — Transmitter output for UART1.
O PWM4 — Pulse Width Modulator output 4.
P0[9]/RXD1/PWM6/
EINT3
76 I RXD1 — Receiver input for UART1.
O PWM6 — Pulse Width Modulator output 6.
I EINT3 — External interrupt 3 input.
P0[10]/RTS1/CAP1[0] 78 O RTS1 — Request to Send output for UART1.
I CAP1[0] — Capture input for Timer 1, channel 0.
P0[11]/CTS1/CAP1[1] 83 I CTS1 — Clear to Send input for UART1.
I CAP1[1] — Capture input for Timer 1, channel 1.
P0[12]/DSR1/MAT1[0] 84 I DSR1 — Data Set Ready input for UART1.
O MAT1[0] — Match output for Timer 1, channel 0.
P0[13]/DTR1/MAT1[1] 85 O DTR1 — Data Terminal Ready output for UART1.
O MAT1[1] — Match output for Timer 1, channel 1.
