11
COMMERCIAL TEMPERATURE RANGE
IDT72V3664 3.3V CMOS SyncBiFIFO
TM
WITH BUS-MATCHING
4,096 x 36 x 2
SIGNAL DESCRIPTION
MASTER RESET (MRS1, MRS2)
After power up, a Master Reset operation must be performed by providing
a LOW pulse to MRS1 and MRS2 simultaneously. Afterwards, each of the
two FIFO memories of the IDT72V3664 undergoes a complete reset by taking
its associated Master Reset (MRS1, MRS2) input LOW for at least four Port A
Clock (CLKA) and four Port B Clock (CLKB) LOW-to-HIGH transitions. The
Master Reset inputs can switch asynchronously to the clocks. A Master Reset
initializes the associated write and read pointers to the first location of the memory
and forces the Full/Input Ready flag (FFA/IRA, FFB/IRB) LOW, the Empty/
Output Ready flag (EFA/ORA, EFB/ORB) LOW, the Almost-Empty flag (AEA,
AEB) LOW and forces the Almost-Full flag (AFA, AFB) HIGH. A Master Reset
also forces the associated Mailbox Flag (MBF1, MFB2) of the parallel mailbox
register HIGH. After a Master Reset, the FIFO's Full/Input Ready flag is set
HIGH after two write clock cycles. Then the FIFO is ready to be written to.
A LOW-to-HIGH transition on the FIFO1 Master Reset (MRS1) input
latches the values of the Big-Endian (BE) input for determining the order by
which bytes are transferred through Port B. It also latches the values of the
Flag Select (FS0, FS1 and FS2) inputs for choosing the Almost-Full and Almost-
Empty offset programming method.
A LOW-to-HIGH transition on the FIFO2 Master Reset (MRS2) clears
the Flag Offset Registers of FIFO2 (X2, Y2). A LOW-to-HIGH transition on the
FIFO2 Master Reset (MRS2) together with the FIFO1 Master Reset (MRS1)
input latches the value of the Big-Endian (BE) input for Port B and also latches
the values of the Flag Select (FS0, FS1 and FS2) inputs for choosing the Almost-
Full and Almost-Empty offset programming method. (For details see Table 1,
Flag Programming, and the Programming the Almost-Empty and Almost-Full
Flags section). The relevant FIFO Master Reset timing diagram can be found
in Figure 3.
PARTIAL RESET (PRS1, PRS2)
Each of the two FIFO memories of these devices undergoes a limited reset
by taking its associated Partial Reset (PRS1, PRS2) input LOW for at least
four Port A Clock (CLKA) and four Port B Clock (CLKB) LOW-to-HIGH
transitions. The Partial Reset inputs can switch asynchronously to the clocks.
A Partial Reset initializes the internal read and write pointers and forces the
Full/Input Ready flag (FFA/IRA, FFB/IRB) LOW, the Empty/Output Ready
flag (EFA/ORA, EFB/ORB) LOW, the Almost-Empty flag (AEA, AEB)
LOW, and the Almost-Full flag (AFA, AFB) HIGH. A Partial Reset also forces
the Mailbox Flag (MBF1, MBF2) of the parallel mailbox register HIGH. After
a Partial Reset, the FIFO’s Full/Input Ready flag is set HIGH after two write
clock cycles. Then the FIFO is ready to be written to.
Whatever flag offsets, programming method (parallel or serial), and timing
mode (FWFT or IDT Standard mode) are currently selected at the time a Partial
Reset is initiated, those settings will be remain unchanged upon completion of
the reset operation. A Partial Reset may be useful in the case where
reprogramming a FIFO following a Master Reset would be inconvenient. See
Figure 4 for the Partial Reset timing diagram.
RETRANSMIT (RT1, RT2)
The FIFO1 memory of these devices undergoes a Retransmit by taking its
associated Retransmit (RT1) input LOW for at least four Port A Clock (CLKA)
and four Port B Clock (CLKB) LOW-to-HIGH transitions. The Retransmit
initializes the read pointer of FIFO1 to the first memory location.
The FIFO2 memory undergoes a Retransmit by taking its associated
Retransmit (RT2) input LOW for at least four Port A Clock (CLKA) and four Port
C Clock (CLKC) LOW-to-HIGH transitions. The Retransmit initializes the read
pointer of FIFO2 to the first memory location.
The RTM pin must be HIGH during the time of Retransmit. Note that the
RT1input is muxed with the PRS1 input, the state of the RTM pin determining
whether this pin performs a Retransmit or Partial Reset. Also, the RT2input is
muxed with the PRS2 input, the state of the RTM pin determining whether this
pin performs a Retransmit or Partial Reset.
BIG-ENDIAN/FIRST WORD FALL THROUGH (BE/FWFT)
— ENDIAN SELECTION
This is a dual purpose pin. At the time of Master Reset, the BE select function
is active, permitting a choice of Big or Little-Endian byte arrangement for data
written to or read from Port B. This selection determines the order by which
bytes (or words) of data are transferred through this port. For the following
illustrations, assume that a byte (or word) bus size has been selected for Port
B. (Note that when Port B is configured for a long word size, the Big-Endian
function has no application and the BE input is a “don’t care”
1
.)
A HIGH on the BE/FWFT input when the Master Reset (MRS1, MRS2)
inputs go from LOW to HIGH will select a Big-Endian arrangement. When data
is moving in the direction from Port A to Port B, the most significant byte (word)
of the long word written to Port A will be read from Port B first; the least significant
byte (word) of the long word written to Port A will be read from Port B last. When
data is moving in the direction from Port B to Port A, the byte (word) written
to Port B first will be read from Port A as the most significant byte (word) of the
long word; the byte (word) written to Port B last will be read from Port A as
the least significant byte (word) of the long word.
A LOW on the BE/FWFT input when the Master Reset (MRS1, MRS2)
inputs go from LOW to HIGH will select a Little-Endian arrangement. When data
is moving in the direction from Port A to Port B, the least significant byte (word)
of the long word written to Port A will be read from Port B first; the most significant
byte (word) of the long word written to Port A will be read from Port B last. When
data is moving in the direction from Port B to Port A, the byte (word) written
to Port B first will be read from Port A as the least significant byte (word) of the
long word; the byte (word) written to Port B last will be read from Port A as
the most significant byte (word) of the long word. Refer to Figure 2 for an
illustration of the BE function. See Figure 3 (Master Reset) for the Endian select
timing diagram.
— TIMING MODE SELECTION
After Master Reset, the FWFT select function is active, permitting a choice
between two possible timing modes: IDT Standard mode or First Word Fall
Through (FWFT) mode. Once the Master Reset (MRS1, MRS2) input is
HIGH, a HIGH on the BE/FWFT input during the next LOW-to-HIGH
transition of CLKA (for FIFO1) and CLKB (for FIFO2) will select IDT Standard
mode. This mode uses the Empty Flag function (EFA, EFB) to indicate
whether or not there are any words present in the FIFO memory. It uses the
Full Flag function (FFA, FFB) to indicate whether or not the FIFO memory
has any free space for writing. In IDT Standard mode, every word read from
the FIFO, including the first, must be requested using a formal read operation.
Once the Master Reset (MRS1, MRS2) input is HIGH, a LOW on the BE/
FWFT input during the next LOW-to-HIGH transition of CLKA (for FIFO1) and
CLKB (for FIFO2) will select FWFT mode. This mode uses the Output Ready
NOTE:
1. Either a HIGH or LOW can be applied to a "don't care" input with no change to the logical operation of the FIFO. Nevertheless, inputs that are temporarily "don't care" (along with
unused inputs) must not be left open, rather they must be either HIGH or LOW.
