OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

UJA1162T,118

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P29
UJA1162 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2014. All rights reserved.
Product data sheet Rev. 2 — 17 April 2014 13 of 29
NXP Semiconductors
UJA1162
Self-supplied high-speed CAN transceiver with Sleep mode
7. Limiting values
[1] When the device is not powered up, I
BUF(max)
= 25 mA.
[2] Verified by an external test house to ensure pins can withstand ISO 7637 part 2 automotive transient test pulses 1, 2a, 3a and 3b.
[3] ESD performance according to IEC 61000-4-2 (150 pF, 330 ) has been verified by an external test house; the result was equal to or
better than 6 kV.
[4] Human Body Model (HBM): according to AEC-Q100-002 (100 pF, 1.5 k).
[5] Pins BUF, VIO and BAT connected to GND, emulating the application circuit.
[6] Machine Model (MM): according to AEC-Q100-003 (200 pF, 0.75 H, 10 ).
[7] Charged Device Model (CDM): according to AEC-Q100-011 (field Induced charge; 4 pF).
[8] In accordance with IEC 60747-1. An alternative definition of virtual junction temperature is: T
vj
=T
amb
+P R
th(j-a)
, where R
th(j-a)
is a
fixed value used in the calculation of T
vj
. The rating for T
vj
limits the allowable combinations of power dissipation (P) and ambient
temperature (T
amb
).
Table 4. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol Parameter Conditions Min Max Unit
V
x
voltage on pin x DC value
pins BUF
[1]
, VIO 0.2 +6 V
pins TXD, RXD, SLPN, CTS 0.2 V
IO
+0.2 V
pins WAKE, INH 18 +40 V
pin BAT 0.2 +40 V
pins CANH and CANL with respect to any
other pin
58 +58 V
V
(CANH-CANL)
voltage between pin CANH
and pin CANL
40 +40 V
V
trt
transient voltage on pins
BAT: via reverse polarity diode and capacitor
to ground
CANL, CANH, WAKE: coupling via 1 nF
capacitors
[2]
150 +100 V
V
ESD
electrostatic discharge
voltage
IEC 61000-4-2
[3]
on pins CANH and CANL; pin BAT with
capacitor; pin WAKE with 10 nF capacitor
and 10 k resistor
6+6 kV
HBM
[4]
on pins CANH, CANL
[5]
8+8 kV
on pins BAT, WAKE 4+4 kV
on any other pin 2+2 kV
MM
[6]
on any pin 100 +100 V
CDM
[7]
on corner pins 750 +750 V
on any other pin 500 +500 V
T
vj
virtual junction temperature
[8]
40 +150 C
T
stg
storage temperature 55 +175 C
UJA1162 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2014. All rights reserved.
Product data sheet Rev. 2 — 17 April 2014 14 of 29
NXP Semiconductors
UJA1162
Self-supplied high-speed CAN transceiver with Sleep mode
8. Thermal characteristics
[1] According to JEDEC JESD51-2, JESD51-5 and JESD51-7 at natural convection on 2s2p board. Board with two inner copper layers
(thickness: 35 m) and thermal via array under the exposed pad connected to the first inner copper layer (thickness: 70 m).
9. Static characteristics
Table 5. Thermal characteristics
Symbol Parameter Conditions Typ Unit
R
th(vj-a)
thermal resistance from virtual junction to ambient
[1]
60 K/W
Table 6. Static characteristics
T
vj
=
40
C to +150
C; V
BAT
=4.5V to 28V; V
IO
= 2.85 V to 5.5 V; R
(CANH-CANL)
=60
; all voltages are defined with respect
to ground; positive currents flow into the IC; typical values are given at V
BAT
= 13 V; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
Supply; pin BAT
V
th(det)pon
power-on detection threshold
voltage
V
BAT
rising 4.2 - 4.55 V
V
th(det)poff
power-off detection threshold
voltage
V
BAT
falling 2.8 - 3 V
V
uvr(CAN)
CAN undervoltage recovery
voltage
V
BAT
rising 4.5 - 5 V
V
uvd(CAN)
CAN undervoltage detection
voltage
V
BAT
falling 4.2 - 4.55 V
I
BAT
battery supply current Standby mode; CAN Offline
mode; 40 C < T
vj
<+85C;
V
BAT
= 7 V to 18 V
-5881A
Sleep mode; CAN Offline mode;
40 C < T
vj
<+85C;
V
BAT
= 7 V to 18 V
-4462A
additional current in CAN Offline
Bias mode; 40 C < T
vj
<85C
-4663A
Normal mode; CAN Active
mode; CAN recessive;
V
TXD
=V
IO
-47.5mA
Normal mode; CAN Active
mode; CAN dominant;
V
TXD
=0 V
-4667mA
Voltage source; pin BUF
V
O
output voltage V
BAT
= 5.5 V to 18 V 4.9 5 5.1 V
V
uvd
undervoltage detection voltage 4.5 - 4.75 V
I
O(sc)
short-circuit output current 300 - 150 mA
Supply; pin VIO
V
uvd
undervoltage detection voltage 2.7 - 2.85 V
I
I(VIO)
input current on pin VIO Standby/Normal mode;
40 C < T
vj
<85C
-7.111A
Sleep mode;
40 C < T
vj
<85C
-5.99.5A
UJA1162 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2014. All rights reserved.
Product data sheet Rev. 2 — 17 April 2014 15 of 29
NXP Semiconductors
UJA1162
Self-supplied high-speed CAN transceiver with Sleep mode
Sleep mode control input; pin SLPN
V
th(sw)
switching threshold voltage 0.25V
IO
-0.75V
IO
V
R
pd
pull-down resistance 40 60 80 k
Inhibit output: pin INH
V
O
output voltage I
INH
= 180 AV
BAT
0.8 - V
BAT
V
R
pd
pull-down resistance Sleep mode 3 4 5 M
CAN transmit data input; pin TXD
V
th(sw)
switching threshold voltage 0.25V
IO
-0.75V
IO
V
R
pu
pull-up resistance 40 60 80 k
CAN transmitter status; pin CTS
I
OH
HIGH-level output current V
CTS
=V
IO
0.4 V;
transmitter on
--4mA
I
OL
LOW-level output current V
CTS
=0.4V;
transmitter off
4 --mA
CAN receive data output; pin RXD
V
OH
HIGH-level output voltage I
OH
= 4mA V
IO
0.4--V
V
OL
LOW-level output voltage I
OL
= 4 mA - - 0.4 V
R
pu
pull-up resistance CAN Offline mode 40 60 80 k
Local wake input; pin WAKE
V
th(sw)r
rising switching threshold
voltage
2.8 - 4.1 V
V
th(sw)f
falling switching threshold
voltage
2.4 - 3.75 V
V
hys(i)
input hysteresis voltage 250 - 800 mV
I
i
input current T
vj
= 40 C to +85 C--1.5A
High-speed CAN bus lines; pins CANH and CANL
V
O(dom)
dominant output voltage CAN Active mode;
V
TXD
= 0 V; V
BAT
> 5.5 V
pin CANH 2.75 3.5 4.5 V
pin CANL 0.5 1.5 2.25 V
V
TXsym
transmitter voltage symmetry V
TXsym
= V
CANH
+V
CANL
;
f
TXD
= 250 kHz; C
SPLIT
=4.7nF
[1]
[2]
0.9V
BUF
-1.1V
BUF
V
V
dom(TX)sym
transmitter dominant voltage
symmetry
V
dom(TX)sym
=
V
BUF
V
CANH
V
CANL
;
V
BAT
> 5.5 V
400 - +400 mV
V
O(dif)bus
bus differential output voltage CAN Active mode (dominant);
V
TXD
= 0 V; V
BAT
> 5.5 V
R
(CANH-CANL)
= 45 to 65 ;
1.5 - 3.0 V
CAN Active mode (recessive);
CAN Offline mode; V
TXD
= V
IO
;
R
(CANH-CANL)
= no load;
V
BAT
> 5.5 V; T
vj
< 150 C
50 - +50 mV
Table 6. Static characteristics …continued
T
vj
=
40
C to +150
C; V
BAT
=4.5V to 28V; V
IO
= 2.85 V to 5.5 V; R
(CANH-CANL)
=60
; all voltages are defined with respect
to ground; positive currents flow into the IC; typical values are given at V
BAT
= 13 V; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P29

UJA1162T,118

Mfr. #:
Buy UJA1162T,118
Manufacturer:
NXP Semiconductors
Description:
IC TRANSCEIVER 14SOIC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet