OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

SI8660BA-A-IS1

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36
Rev. 1.3 7
Si8660/61/62/63
Figure 1. Propagation Delay Timing
Timing Characteristics
Si866xBx, Ex
Maximum Data Rate 0 — 150 Mbps
Minimum Pulse Width — — 5.0 ns
Propagation Delay t
PHL
, t
PLH
See Figure 1 5.0 8.0 13 ns
Pulse Width Distortion
|t
PLH
-
t
PHL
|
PWD See Figure 1 — 0.2 4.5 ns
Propagation Delay Skew
2
t
PSK(P-P)
—2.04.5ns
Channel-Channel Skew t
PSK
—0.42.5ns
All Models
Output Rise Time t
r
C
L
=15pF
See Figure 1
—
2.5 4.0
ns
Output Fall Time t
f
C
L
=15pF
See Figure 1
—
2.5 4.0
ns
Peak Eye Diagram Jitter t
JIT(PK)
See Figure 6 — 350 — ps
Common Mode
Transient Immunity
CMTI V
I
=V
DD
or 0 V 35 50 — kV/µs
Startup Time
3
t
SU
—1540µs
Table 2. Electrical Characteristics (Continued)
(V
DD1
= 5 V ±10%, V
DD2
= 5 V ±10%, T
A
=–40 to 125ºC)
Parameter Symbol Test Condition Min Typ Max Unit
Notes:
1. The nominal output impedance of an isolator driver channel is approximately 50 , ±40%, which is a combination of
the value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads
where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
2. t
PSK(P-P)
is the magnitude of the difference in propagation delay times measured between different units operating at
the same supply voltages, load, and ambient temperature.
3. Start-up time is the time period from the application of power to valid data at the output.
Typical
Input
t
PLH
t
PHL
Typical
Output
t
r
t
f
90%
10%
90%
10%
1.4 V
1.4 V
8 Rev. 1.3
Si8660/61/62/63
Table 3. Electrical Characteristics
(V
DD1
= 3.3 V ±10%, V
DD2
= 3.3 V ±10%, T
A
= –40 to 125 ºC)
Parameter Symbol Test Condition Min Typ Max Unit
VDD Undervoltage Threshold VDDUV+ V
DD1
, V
DD2
rising 1.95 2.24 2.375 V
VDD Undervoltage Threshold VDDUV– V
DD1
, V
DD2
falling 1.88 2.16 2.325 V
VDD Negative-Going Lockout
Hysteresis
VDD
HYS
50 70 95 mV
Positive-Going Input Threshold VT+ All inputs rising 1.4 1.67 1.9 V
Negative-Going Input Threshold VT– All inputs falling 1.0 1.23 1.4 V
Input Hysteresis V
HYS
0.38 0.44 0.50 V
High Level Input Voltage V
IH
2.0 — — V
Low Level Input Voltage V
IL
——0.8V
High Level Output Voltage V
OH
loh = –4 mA V
DD1
,V
DD2
–0.4 3.1 — V
Low Level Output Voltage V
OL
lol = 4 mA — 0.2 0.4 V
Input Leakage Current I
L
——±10µA
Output Impedance
1
Z
O
—50—
DC Supply Current (All inputs 0 V or at supply)
Si8660Bx, Ex
V
DD1
V
DD2
V
DD1
V
DD2
V
I
=0(Bx), 1(Ex)
V
I
=0(Bx), 1(Ex)
V
I
=1(Bx), 0(Ex)
V
I
=1(Bx), 0(Ex)
—
—
—
—
1.2
3.5
8.8
3.7
1.9
5.3
12.3
5.6
mA
Si8661Bx, Ex
V
DD1
V
DD2
V
DD1
V
DD2
V
I
=0(Bx), 1(Ex)
V
I
=0(Bx), 1(Ex)
V
I
=1(Bx), 0(Ex)
V
I
=1(Bx), 0(Ex)
—
—
—
—
1.7
3.4
7.9
4.8
2.7
5.1
11.1
7.2
mA
Si8662Bx, Ex
V
DD1
V
DD2
V
DD1
V
DD2
V
I
=0(Bx), 1(Ex)
V
I
=0(Bx), 1(Ex)
V
I
=1(Bx), 0(Ex)
V
I
=1(Bx), 0(Ex)
—
—
—
—
2.2
3.0
7.5
5.6
3.3
4.5
10.5
8.4
mA
Si8663Bx, Ex
V
DD1
V
DD2
V
DD1
V
DD2
V
I
=0(Bx), 1(Ex)
V
I
=0(Bx), 1(Ex)
V
I
=1(Bx), 0(Ex)
V
I
=1(Bx), 0(Ex)
—
—
—
—
2.6
2.6
6.5
6.5
3.9
3.9
9.1
9.1
mA
Notes:
1. The nominal output impedance of an isolator driver channel is approximately 50 , ±40%, which is a combination of the
value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads
where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
2. t
PSK(P-P)
is the magnitude of the difference in propagation delay times measured between different units operating at
the same supply voltages, load, and ambient temperature.
3. Start-up time is the time period from the application of power to valid data at the output.
Rev. 1.3 9
Si8660/61/62/63
1 Mbps Supply Current (All inputs = 500 kHz square wave, CI = 15 pF on all outputs)
Si8660Bx, Ex
V
DD1
V
DD2
—
—
5.0
4.2
7.0
5.9
mA
Si8661Bx, Ex
V
DD1
V
DD2
—
—
4.9
4.6
6.9
6.4
mA
Si8662Bx, Ex
V
DD1
V
DD2
—
—
5.1
4.7
7.1
6.6
mA
Si8663Bx, Ex
V
DD1
V
DD2
—
—
4.9
4.9
6.8
6.8
mA
10 Mbps Supply Current (All inputs = 5 MHz square wave, CI = 15 pF on all outputs)
Si8660Bx, Ex
V
DD1
V
DD2
—
—
5.0
5.0
7.0
7.0
mA
Si8661Bx, Ex
V
DD1
V
DD2
—
—
5.0
5.3
7.0
7.4
mA
Si8662Bx, Ex
V
DD1
V
DD2
—
—
5.3
5.2
7.4
7.3
mA
Si8663Bx, Ex
V
DD1
V
DD2
—
—
5.2
5.2
7.3
7.3
mA
Table 3. Electrical Characteristics (Continued)
(V
DD1
= 3.3 V ±10%, V
DD2
= 3.3 V ±10%, T
A
= –40 to 125 ºC)
Parameter Symbol Test Condition Min Typ Max Unit
Notes:
1. The nominal output impedance of an isolator driver channel is approximately 50 , ±40%, which is a combination of the
value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads
where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
2. t
PSK(P-P)
is the magnitude of the difference in propagation delay times measured between different units operating at
the same supply voltages, load, and ambient temperature.
3. Start-up time is the time period from the application of power to valid data at the output.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36

SI8660BA-A-IS1

Mfr. #:
Buy SI8660BA-A-IS1
Manufacturer:
Silicon Labs
Description:
Digital Isolators 6 Ch 1 kV Isolator 150M 6/0 NB
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet