Philips Semiconductors Preliminary data
P89C51RA2/RB2/RC2/RD2xx80C51 8-bit Flash microcontroller family
8KB/16KB/32KB/64KB ISP/IAP Flash with 512B/512B/512B/1KB RAM
2002 Jul 18
56
DC ELECTRICAL CHARACTERISTICS
T
amb
= 0 °C to +70 °C or –40 °C to +85 °C; V
CC
= 5 V ± 10%; V
SS
= 0 V
TEST
LIMITS
CONDITIONS
MIN TYP
1
MAX
V
IL
Input low voltage 4.5 V < V
CC
< 5.5 V –0.5 0.2V
CC
–0.1 V
V
IH
Input high voltage (ports 0, 1, 2, 3, EA) 0.2V
CC
+0.9 V
CC
+0.5 V
V
IH1
Input high voltage, XTAL1, RST 0.7V
CC
V
CC
+0.5 V
V
OL
Output low voltage, ports 1, 2, 3
8
V
CC
= 4.5 V
I
OL
= 1.6 mA
2
0.4 V
V
OL1
Output low voltage, port 0, ALE, PSEN
7,
8
V
CC
= 4.5 V
I
OL
= 3.2 mA
2
0.45 V
V
OH
Output high voltage, ports 1, 2, 3
3
V
CC
= 4.5 V
I
OH
= –30 µA
V
CC
– 0.7 V
V
OH1
Output high voltage (port 0 in external bus mode),
ALE
9
, PSEN
3
V
CC
= 4.5 V
I
OH
= –3.2 mA
V
CC
– 0.7 V
I
IL
Logical 0 input current, ports 1, 2, 3 V
IN
= 0.4 V –1 –75 µA
I
TL
Logical 1-to-0 transition current, ports 1, 2, 3
6
V
IN
= 2.0 V
See Note 4
–650 µA
I
LI
Input leakage current, port 0 0.45 < V
IN
< V
CC
– 0.3 ±10 µA
I
CC
Power supply current (see Figure 49): See Note 5
Active mode (see Note 5)
Idle mode (see Note 5)
Power-down mode or clock stopped (see
T
amb
= 0 °C to 70 °C < 30 100 µA
Figure 55 for conditions)
T
amb
= –40 °C to +85 °C < 40 125 µA
Programming and erase mode f
osc
= 20 MHz 60 mA
R
RST
Internal reset pull-down resistor 40 225 kΩ
C
IO
Pin capacitance
10
(except EA) 15 pF
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5 V.
2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V
OL
s of ALE and ports 1 and 3. The noise is due
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100 pF), the noise pulse on the ALE pin may exceed 0.8 V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I
OL
can exceed these conditions provided that no
single output sinks more than 5 mA and no more than two outputs exceed the test conditions.
3. Capacitive loading on ports 0 and 2 may cause the V
OH
on ALE and PSEN to momentarily fall below the V
CC
–0.7 specification when the
address bits are stabilizing.
4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when V
IN
is approximately 2 V.
5. See Figures 52 through 55 for I
CC
test conditions and Figure 49 for I
CC
vs Freq.
Active mode: I
CC(MAX)
= (10.5 + 0.9 × FREQ.[MHz])mA in 12-clock mode
Idle mode: I
CC(MAX)
= (2.5 + 0.33 × FREQ.[MHz])mA in 12-clock mode
6. This value applies to T
amb
= 0 °C to +70 °C.
7. Load capacitance for port 0, ALE, and PSEN
= 100 pF, load capacitance for all other outputs = 80 pF.
8. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin: 15 mA (*NOTE: This is 85 °C specification.)
Maximum I
OL
per 8-bit port: 26 mA
Maximum total I
OL
for all outputs: 71 mA
If I
OL
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
9. ALE is tested to V
OH1
, except when ALE is off then V
OH
is the voltage specification.
10.Pin capacitance is characterized but not tested. Pin capacitance is less than 25 pF. Pin capacitance of ceramic package is less than 15 pF
(except EA
is 25 pF).
