3
COMMERCIAL TEMPERATURE RANGE
IDT72V3656/72V3666/72V3676 3.3V CMOS TRIPLE BUS SyncFIFO
TM
WITH BUS MATCHING 2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2
each port are independent of one another and can be asynchronous or
coincident. The enables for each port are arranged to provide a simple
bidirectional interface between microprocessors and/or buses with synchro-
nous control.
Communication between each port may bypass the FIFOs via two mailbox
registers. The mailbox registers' width matches the selected bus width of ports
B and C. Each mailbox register has a flag (MBF1 and MBF2) to signal when
new mail has been stored.
Two kinds of reset are available on these FIFOs: Master Reset and Partial
Reset. Master Reset initializes the read and write pointers to the first location
of the memory array and selects serial flag programming, parallel flag program-
ming, or one of five possible default flag offset settings, 8, 16, 64, 256 or 1,024.
Each FIFO has its own, independent Master Reset pin, MRS1 and MRS2.
Partial Reset also sets the read and write pointers to the first location of the
memory. Unlike Master Reset, any settings existing prior to Partial Reset (i.e.,
programming method and partial flag default offsets) are retained. Partial Reset
is useful since it permits flushing of the FIFO memory without changing any
configuration settings. Each FIFO has its own, independent Partial Reset pin,
PRS1 and PRS2. Note that the Retransmit Mode, RTM pin must be LOW at
the point a partial reset is performed.
Both FIFO's have Retramsmit capability, when a Retransmit is performed
on a respective FIFO only the read pointer is reset to the first memory location.
A Retransmit is performed by using the Retransmit Mode, RTM pin in conjunction
with the Retransmit pins RT1 or RT2, for each respective FIFO. Note that the
two Retransmit pins RT1 and RT2 are muxed with the Partial Reset pins.
These devices have two modes of operation: In the IDT Standard mode,
the first word written to an empty FIFO is deposited into the memory array. A
read operation is required to access that word (along with all other words
residing in memory). In the First Word Fall Through mode (FWFT), the first
word written to an empty FIFO appears automatically on the outputs, no read
operation required (Nevertheless, accessing subsequent words does neces-
sitate a formal read request). The state of the BE/FWFT pin during Master
Reset determines the mode in use.
Each FIFO has a combined Empty/Output Ready Flag (EFA/ORA and
EFB/ORB) and a combined Full/Input Ready Flag (FFA/IRA and FFC/
IRC). The EF and FF functions are selected in the IDT Standard mode. EF
indicates whether or not the FIFO memory is empty. FF shows whether the
memory is full or not. The IR and OR functions are selected in the First Word
Fall Through mode. IR indicates whether or not the FIFO has available memory
locations. OR shows whether the FIFO has data available for reading or not.
It marks the presence of valid data on the outputs.
Each FIFO has a programmable Almost-Empty flag (AEA and AEB) and
a programmable Almost-Full flag (AFA and AFC). AEA and AEB indicate when
a selected number of words remain in the FIFO memory. AFA and AFC indicate
when the FIFO contains more than a selected number of words.
FFA/IRA, FFC/IRC, AFA and AFC are two-stage synchronized to the
Port Clock that writes data into its array. EFA/ORA, EFB/ORB, AEA, and
AEB are two-stage synchronized to the Port Clock that reads data from its array.
Programmable offsets for AEA, AEB, AFA, AFC are loaded in parallel using
Port A or in serial via the SD input. Five default offset settings are also provided.
The AEA and AEB threshold can be set at 8, 16, 64, 256, and 1,024 locations
from the empty boundary and the AFA and AFC threshold can be set at 8,
16, 64, 256 or 1,024 locations from the full boundary. All these choices are made
using the FS0, FS1 and FS2 inputs during Master Reset.
Interspersed Parity can also be selected during a Master Reset of the
FIFO. If Interspersed Parity is selected then during parallel programming of the
flag offset values, the device will ignore data line A8. If Non-Interspersed Parity
is selected then data line A8 will become a valid bit.
A Loopback function is provided on Port A. When the Loop feature is
selected via the LOOP pin, the data output from FIFO2 will be directed to the
data input of FIFO1. If Loop is selected and Port A is set-up for write operation
via W/RA pin, then data output from FIFO2 will be written to FIFO1, but will not
be placed on the output Port A (A0-A35). If Port A is set-up for read operation
via W/RA then data output from FIFO2 will be written into FIFO1 and placed onto
Port A (A0-A35). The Loop will continue to happen provided that FIFO1 is not
full and FIFO2 is not empty. If during a Loop sequence FIFO1 becomes full then
any data that continues to be read out from FIFO2 will only be placed on the
Port A (A0-A35) lines, provided that Port A is set-up for read operation. If during
a Loop sequence the FIFO2 becomes empty, then the last word from FIFO2
will continue to be clocked into FIFO1 until FIFO1 becomes full or until the Loop
function is stopped. The Loop feature can be useful when performing system
debugging and remote loopbacks.
Two or more FIFOs may be used in parallel to create wider data paths.
Such a width expansion requires no additional, external components. Further-
more, two IDT72V3656/72V3666/72V3676 FIFOs can be combined with
unidirectional FIFOs capable of First Word Fall Through timing (i.e. the
SuperSync FIFO family) to form a depth expansion.
If, at any time, the FIFO is not actively performing a function, the chip will
automatically power down. During the power down state, supply current
consumption (ICC) is at a minimum. Initiating any operation (by activating control
inputs) will immediately take the device out of the power down state.
The IDT72V3656/72V3666/72V3676 are characterized for operation from
0°C to 70°C. Industrial temperature range (-40°C to +85°C) is available by
special order. They are fabricated using IDT’s high speed, submicron CMOS
technology.