OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

SC16C652BIBS,157

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P43
SC16C652B_4 © Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet Rev. 04 — 1 September 2005 16 of 43
Philips Semiconductors
SC16C652B
Dual UART with 32-byte FIFOs and IrDA encoder/decoder
7.1 Transmit (THR) and Receive (RHR) Holding Registers
The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and
Transmit Shift Register (TSR). The status of the THR is provided in the Line Status
Register (LSR). Writing to the THR transfers the contents of the data bus (D7 to D0) to the
TSR and UART via the THR, providing that the THR is empty. The THR empty flag in the
LSR will be set to a logic 1 when the transmitter is empty or when data is transferred to the
TSR. Note that a write operation can be performed when the THR empty flag is set
(logic 0 = at least one byte in FIFO/THR, logic 1 = FIFO/THR empty).
The serial receive section also contains an 8-bit Receive Holding Register (RHR) and a
Receive Serial Shift Register (RSR). Receive data is removed from the SC16C652B and
receive FIFO by reading the RHR. The receive section provides a mechanism to prevent
false starts. On the falling edge of a start or false start bit, an internal receiver counter
starts counting clocks at the 16× clock rate. After 7
1
⁄
2
clocks, the start bit time should be
shifted to the center of the start bit. At this time the start bit is sampled, and if it is still a
logic 0 it is validated. Evaluating the start bit in this manner prevents the receiver from
assembling a false character. Receiver status codes will be posted in the LSR.
7.2 Interrupt Enable Register (IER)
The Interrupt Enable Register (IER) masks the interrupts from receiver ready, transmitter
empty, line status and modem status registers. These interrupts would normally be seen
on the INTA, INTB output pins.
Table 10: Interrupt Enable Register bits description
Bit Symbol Description
7 IER[7] CTS interrupt.
logic 0 = disable the CTS interrupt (normal default condition)
logic 1 = enable the CTS interrupt. The SC16C652B issues an interrupt when
the CTS pin transitions from a logic 0 to a logic 1.
6 IER[6] RTS interrupt.
logic 0 = disable the RTS interrupt (normal default condition)
logic 1 = enable the RTS interrupt. The SC16C652B issues an interrupt when
the RTS pin transitions from a logic 0 to a logic 1.
5 IER[5] Xoff interrupt.
logic 0 = disable the software flow control, receive Xoff interrupt (normal
default condition)
logic 1 = enable the software flow control, receive Xoff interrupt.
4 IER[4] Sleep mode.
logic 0 = disable Sleep mode (normal default condition)
logic 1 = enable Sleep mode
3 IER[3] Modem Status Interrupt. This interrupt will be issued whenever there is a modem
status change as reflected in MSR[3:0].
logic 0 = disable the modem status register interrupt (normal default condition)
logic 1 = enable the modem status register interrupt
2 IER[2] Receive Line Status interrupt. This interrupt will be issued whenever a receive
data error condition exists as reflected in LSR[4:1].
logic 0 = disable the receiver line status interrupt (normal default condition)
logic 1 = enable the receiver line status interrupt
SC16C652B_4 © Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet Rev. 04 — 1 September 2005 17 of 43
Philips Semiconductors
SC16C652B
Dual UART with 32-byte FIFOs and IrDA encoder/decoder
7.2.1 IER versus Transmit/Receive FIFO interrupt mode operation
When the receive FIFO (FCR[0] = logic 1), and receive interrupts (IER[0] = logic 1) are
enabled, the receive interrupts and register status will reflect the following:
• The receive RXRDY interrupt (Level 2 ISR interrupt) is issued to the external CPU
when the receive FIFO has reached the programmed trigger level. It will be cleared
when the receive FIFO drops below the programmed trigger level.
• Receive FIFO status will also be reflected in the user accessible ISR register when
the receive FIFO trigger level is reached. Both the ISR register receive status bit and
the interrupt will be cleared when the FIFO drops below the trigger level.
• The receive data ready bit (LSR[0]) is set as soon as a character is transferred from
the shift register (RSR) to the receive FIFO. It is reset when the FIFO is empty.
• When the Transmit FIFO and interrupts are enabled, an interrupt is generated when
the transmit FIFO is empty due to the unloading of the data by the TSR and UART for
transmission via the transmission media. The interrupt is cleared either by reading the
ISR, or by loading the THR with new data characters.
7.2.2 IER versus Receive/Transmit FIFO polled mode operation
When FCR[0] = logic 1, resetting IER[3:0] enables the SC16C652B in the FIFO polled
mode of operation. In this mode, interrupts are not generated and the user must poll the
LSR register for TX and/or RX data status. Since the receiver and transmitter have
separate bits in the LSR either or both can be used in the polled mode by selecting
respective transmit or receive control bit(s).
• LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.
• LSR[4:1] will provide the type of receive errors, or a receive break, if encountered.
• LSR[5] will indicate when the transmit FIFO is empty.
• LSR[6] will indicate when both the transmit FIFO and transmit shift register are empty.
• LSR[7] will show if any FIFO data errors occurred.
1 IER[1] Transmit Holding Register interrupt. In the 16C450 mode, this interrupt will be
issued whenever the THR is empty, and is associated with LSR[5]. In the FIFO
modes, this interrupt will be issued whenever the FIFO is empty.
logic 0 = disable the Transmit Holding Register Empty (TXRDY) interrupt
(normal default condition)
logic 1 = enable the TXRDY (ISR level 3) interrupt
0 IER[0] Receive Holding Register. In the 16C450 mode, this interrupt will be issued when
the RHR has data, or is cleared when the RHR is empty. In the FIFO mode, this
interrupt will be issued when the FIFO has reached the programmed trigger level
or is cleared when the FIFO drops below the trigger level.
logic 0 = disable the receiver ready (ISR level 2, RXRDY) interrupt (normal
default condition)
logic 1 = enable the RXRDY (ISR level 2) interrupt
Table 10: Interrupt Enable Register bits description
…continued
Bit Symbol Description
SC16C652B_4 © Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet Rev. 04 — 1 September 2005 18 of 43
Philips Semiconductors
SC16C652B
Dual UART with 32-byte FIFOs and IrDA encoder/decoder
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger
levels, and select the DMA mode.
7.3.1 DMA mode
7.3.1.1 Mode 0 (FCR bit 3 = 0)
Set and enable the interrupt for each single transmit or receive operation, and is similar to
the 16C450 mode. Transmit Ready (TXRDY) will go to a logic 0 whenever the FIFO (THR,
if FIFO is not enabled) is empty. Receive Ready (RXRDY) will go to a logic 0 whenever the
Receive Holding Register (RHR) is loaded with a character.
7.3.1.2 Mode 1 (FCR bit 3 = 1)
Set and enable the interrupt in a block mode operation. The transmit interrupt is set when
the transmit FIFO is below the programmed trigger level. The receive interrupt is set when
the receive FIFO fills to the programmed trigger level. However, the FIFO continues to fill
regardless of the programmed level until the FIFO is full. RXRDY remains a logic 0 as long
as the FIFO fill level is above the programmed trigger level.
7.3.2 FIFO mode
Table 11: FIFO Control Register bits description
Bit Symbol Description
7:6 FCR[7:6] RCVR trigger. These bits are used to set the trigger level for the receive FIFO
interrupt.
An interrupt is generated when the number of characters in the FIFO equals
the programmed trigger level. However, the FIFO will continue to be loaded
until it is full. Refer to
Table 12.
5:4 FCR[5:4] Logic 0 or cleared is the default condition; TX trigger level = 16.
These bits are used to set the trigger level for the transmit FIFO interrupt.
The SC16C652B will issue a transmit empty interrupt when the number of
characters in FIFO drops below the selected trigger level. Refer to
Table 13.
3 FCR[3] DMA mode select.
logic 0 = set DMA mode ‘0’ (normal default condition)
logic 1 = set DMA mode ‘1’
Transmit operation in mode ‘0’: When the SC16C652B is in the 16C450
mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode (FIFOs
enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there are no
characters in the transmit FIFO or transmit holding register, the
TXRDY pin
will be a logic 0. Once active, the
TXRDY pin will go to a logic 1 after the first
character is loaded into the transmit holding register.
Receive operation in mode ‘0’: When the SC16C652B is in 16C450 mode,
or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and there is at least
one character in the receive FIFO, the
RXRDY pin will be a logic 0. Once
active, the
RXRDY pin will go to a logic 1 when there are no more characters
in the receiver.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P43

SC16C652BIBS,157

Mfr. #:
Buy SC16C652BIBS,157
Manufacturer:
NXP Semiconductors
Description:
UART Interface IC 16CB 2.5V-5V 2CH
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet