OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

R5F21336TNFP#50

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P50
R8C/33T Group 5. Electrical Characteristics
R01DS0046EJ0110 Rev.1.10 Page 40 of 47
Apr 26, 2011
Table 5.20 Electrical Characteristics (4) [2.7 V ≤ Vcc < 3.3 V]
(Topr =
−
20
°
C to 85
°
C (N version), unless otherwise specified.)
Symbol Parameter Condition
Standard
Unit
Min. Typ. Max.
I
CC Power supply current
(Vcc = 2.7 V to 3.3 V)
Single-chip mode,
output pins are open,
other pins are Vss
High-speed
clock mode
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
—3.510mA
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
—1.57.5mA
High-speed
on-chip
oscillator
mode
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
—715mA
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
—3—mA
XIN clock off
High-speed on-chip oscillator on fOCO-F = 10 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
—4—mA
XIN clock off
High-speed on-chip oscillator on fOCO-F = 10 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
—1.5—mA
XIN clock off
High-speed on-chip oscillator on fOCO-F = 4 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-16
MSTTRD = MSTTRC = 1
—1—mA
Low-speed
on-chip
oscillator
mode
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8, FMR27 = 1, VCA20 = 0
—90390µA
Wait mode
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock operation
VCA27 = VCA26 = VCA25 = 0, VCA20 = 1
—1590µA
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0, VCA20 = 1
—480µA
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
While a WAIT instruction is executed
VCA27 = VCA26 = VCA25 = 0, VCA20 = 1
—3.5—µA
Stop mode
XIN clock off, Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
—25.0µA
XIN clock off, Topr = 85°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
—5—µA
R8C/33T Group 5. Electrical Characteristics
R01DS0046EJ0110 Rev.1.10 Page 41 of 47
Apr 26, 2011
Timing requirements
(Unless Otherwise Specified: Vcc = 3 V, Vss = 0 V at Topr = 25°C)
Figure 5.8 External Clock Input Timing Diagram when Vcc = 3 V
Figure 5.9 TRAIO Input Timing Diagram when Vcc = 3 V
Table 5.21 External Clock Input (XOUT)
Symbol Parameter
Standard
Unit
Min. Max.
t
c(XOUT) XOUT input cycle time 50 — ns
t
WH(XOUT) XOUT input “H” width 24 — ns
t
WL(XOUT) XOUT input “L” width 24 — ns
Table 5.22 TRAIO Input
Symbol Parameter
Standard
Unit
Min. Max.
t
c(TRAIO) TRAIO input cycle time 300 — ns
t
WH(TRAIO) TRAIO input “H” width 120 — ns
t
WL(TRAIO) TRAIO input “L” width 120 — ns
Vcc = 3 V
External
clock input
tC(XOUT)
tWH(XOUT)
tWL(XOUT)
Vcc = 3 V
TRAIO input
tC(TRAIO)
tWH(TRAIO)
tWL(TRAIO)
R8C/33T Group 5. Electrical Characteristics
R01DS0046EJ0110 Rev.1.10 Page 42 of 47
Apr 26, 2011
i = 0 to 2
Figure 5.10 Serial Interface Timing Diagram when Vcc = 3 V
Notes:
1. When selecting the digital filter by the INTi
input filter select bit, use an INTi input HIGH width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
2. When selecting the digital filter by the INTi
input filter select bit, use an INTi input LOW width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
Figure 5.11 Input Timing for External Interrupt INTi and Key Input Interrupt KIi when Vcc = 3 V
Table 5.23 Serial Interface
Symbol Parameter
Standard
Unit
Min. Max.
t
c(CK) CLKi input cycle time 300 — ns
t
W(CKH) CLKi input “H” width 150 — ns
t
W(CKL) CLKi Input “L” width 150 — ns
t
d(C-Q) TXDi output delay time — 80 ns
t
h(C-Q) TXDi hold time 0 — ns
t
su(D-C) RXDi input setup time 70 — ns
t
h(C-D) RXDi input hold time 90 — ns
Table 5.24 External Interrupt INTi (i = 0 to 3) Input, Key Input Interrupt KIi (i = 0 to 3)
Symbol Parameter
Standard
Unit
Min. Max.
t
W(INH)
INTi input “H” width, KIi input “H” width
380
(1)
—ns
t
W(INL)
INTi input “L” width, KIi input “L” width
380
(2)
—ns
Vcc = 3 V
CLKi
TXDi
RXDi
th(C-D)
tC(CK)
tW(CKH)
tW(CKL)
td(C-Q) tsu(D-C)
th(C-Q)
i = 0 to 2
INTi input
(i = 0 to 3)
KIi input
(i = 0 to 3)
Vcc = 3 V
tW(INL)
tW(INH)
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P50

R5F21336TNFP#50

Mfr. #:
Buy R5F21336TNFP#50
Manufacturer:
Renesas Electronics
Description:
16-bit Microcontrollers - MCU R8/C33T 32+4K 1.8/5.5V -20TO85 32LQFP TR
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet