© Semiconductor Components Industries, LLC, 2018
January, 2018 − Rev. 0
1 Publication Order Number:
NCP13992/D
NCP13992
High Performance Current
Mode Resonant Controller
with Integrated High-
Voltage Drivers
The NCP13992 is a high performance current mode controller for
half bridge resonant converters. This controller implements 600 V
gate drivers, simplifying layout and reducing external component
count. The built−in Brown−Out input function eases implementation
of the controller in all applications. In applications where a PFC front
stage is needed, the NCP13992 features a dedicated output to drive the
PFC controller. This feature together with quiet skip mode technique
further improves light load efficiency of the whole application. The
NCP13992 provides a suite of protection features allowing safe
operation in any application. This includes: overload protection,
over−current protection to prevent hard switching cycles, brown−out
detection, open optocoupler detection, automatic dead−time adjust,
over−voltage (OVP) and over−temperature (OTP) protections.
Features
High−Frequency Operation from 20 kHz up to 750 kHz
Current Mode Control Scheme
Automatic Dead−time with Maximum Dead−time Clamp
Dedicated Startup Sequence for Fast Resonant Tank Stabilization
Light Load Operation Mode for Improved Efficiency
Quiet Skip Operation Mode for Minimize Transformer Acoustic Noise
Latched or Auto−Recovery Overload Protection
Latched or Auto−Recovery Output Short Circuit Protection
Latched Input for Severe Fault Conditions, e.g. OVP or OTP
Out of Resonance Switching Protection
Open Feedback Loop Protection
Precise Brown−out Protection
PFC Stage Operation Control According to Load Conditions
Startup Current Source with Extremely Low Leakage Current
Dynamic Self−Supply (DSS) Operation in Off−mode or Fault Modes
Pin to Adjacent Pin / Open Pin Fail Safe
These are Pb−Free Devices
Typical Applications
Adapters and Offline Battery Chargers
Flat Panel Display Power Converters
Computing Power Supplies
Industrial and Medical Power Sources
SOIC−16 NB
(LESS PINS 2 AND 13)
D SUFFIX
CASE 751DU
MARKING DIAGRAM
www.onsemi.com
See detailed ordering and shipping information on page 8 o
f
this data sheet.
ORDERING INFORMATION
1
16
NCP13992 = Specific Device Code
x= A
y= A
A = Assembly Location
WL = Wafer Lot
Y = Year
WW = Work Week
G = Pb−Free Package
PIN CONNECTIONS
1
16
NCP13992xy
AWLYWWG
VBOOT
MUPPER
HB
MLOWER
GND
VCC
HV
VBULK/PFCFB
SKIP
LLCFB
LLCCS
OVP/OTP
1
3
4
5
6
7
8
16
15
14
12
11
10
9
PFCMODEFBFREEZE
(Top View)
NCP13992
www.onsemi.com
2
Figure 1. Typical Application Example without PFC Stage − WLLC Design
Figure 2. Typical Application Example with PFC Stage
NCP13992
www.onsemi.com
3
PIN FUNCTION DESCRIPTION
Pin No. Pin Name Function Pin Description
1 HV High−voltage startup
current source input
Connects to rectified AC line or to bulk capacitor to perform functions of Start−
up Current Source and Dynamic Self−Supply
2 NC Not connected Increases the creepage distance
3 VBULK /
PFC FB
Bulk voltage monitoring input Receives divided bulk voltage to perform Brown−out protection.
4 SKIP Skip threshold adjust Sets the skip in threshold via a resistor connected to ground
5 LLC FB LLC feedback input Defines operating frequency based on given load conditions. Activates skip
mode operation under light load conditions.
6 LLC CS LLC current sense input Senses divided resonant capacitor voltage to perform on−time modulation, out
of resonant switching protection, over−current protection and secondary side
short circuit protection.
7 OTP / OVP Over−temperature and
over−voltage protection input
Implements over−temperature and over−voltage protection on single pin.
8 FB FREEZE Minimum internal FB level Adjusts minimum internal FB level that can be reached during light load oper-
ation.
9 PFC MODE PFC and external HV
switch control output
Provides supply voltage for PFC front stage controller and/or enables Vbulk
sensing network HV switch.
10 VCC Supplies the controller The controller accepts up to 20 V on VCC pin
11 GND Analog ground Common ground connection for adjust components, sensing networks and
DRV outputs.
12 MLOWER Low side driver output Drives the lower side MOSFET
13 NC Not connected Increases the creepage distance
14 MUPPER High side driver output Drives the higher side MOSFET
15 HB Half−bridge connection Connects to the half−bridge output.
16 VBOOT Bootstrap pin The floating VCC supply for the upper stage
Figure 3. Internal Circuit Architecture

NCP13992AADR2G

Mfr. #:
Manufacturer:
ON Semiconductor
Description:
AC/DC Converters HIGH PERF CURRENT
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet