NCP81274
www.onsemi.com
25
PHTH1 to PHTH4 Status Registers
(0x3B, 0x3D, 0x3F 0x41)
These registers contain the phase shedding threshold
values set by the resistors connected to the PHTH
X
pins. The
values of the thresholds are updated on every rising edge of
the EN signal. The resistor values should be chosen to ensure
that the voltage drop across them developed by the 10 mA
current sourced by the NCP81274 during power-up (EN set
high) matches the value of the READ_IOUT register (0x26)
at the desired load current. Setting the resistors to generate
a voltage above 2 V will disable the PHTH
X
threshold for
that pin.
Phase Shedding Hysteresis Register (0x44)
This register sets the hysteresis during a transition from
a high count phase to a low count phase configuration. The
hysteresis is expressed in codes (LSBs) of the PHTH
X
threshold values.
Phase Shedding Delay Register (0x45)
This register sets the delay during a transition from a high
count phase to a low count phase configuration. The
power-up default value is 200 ms and it can be dynamically
changed in steps of 10 ms (1 LSB) through the I
2
C interface.
Second Function Configuration Register
Latch A and B Registers (0x46, 0x47)
These registers allow the user to select whether the second
functions settings (LL, Soft Start, OCP, LPC and PHTH
X
)
are controlled by the external resistors or the configuration
registers (see Table 24). When/EN is toggled the default
control mode for the second functions is the external resistor.
Switching between the two modes can be done by simply
writing the appropriate byte (the same byte) to both registers
(the order doesn’t matter).
Table 24. SECOND CONFIGURATION LATCH
REGISTER A AND B
Bits
Second Function
Configuration
Register
Description
7:6 Reserved N/A
5 FSW 0 = set by external resistor
(see Table 19)
1 = set by register 0x30
(see Table 19)
4 LL 0 = set by external resistor
(see Table 5)
1 = set by register 0x39
3 Reserved N/A
2 OCP 0 = set by external resistor
(see Table 9)
1= set by register 0x2E
1 Reserved N/A
0 PHTH
X
0 = set by external resistors
connected between PHTH
X
pins
and GND
1 = set by registers 0x3A, 0x3C,
0x3E and 0x40
NCP81274
www.onsemi.com
26
PACKAGE DIMENSIONS
QFN40 5x5, 0.4P
CASE 485CR
ISSUE C
SEATING
NOTE 4
0.15 C
(A3)
A
A1
D2
b
1
11
21
40
E2
40X
L
40X
BOTTOM VIEW
TOP VIEW
SIDE VIEW
D
A
B
E
0.15
C
PIN ONE
LOCATION
0.10 C
0.08 C
C
e
PLANE
NOTE 3
L1
DETAIL A
L
ALTERNATE TERMINAL
CONSTRUCTIONS
L
DETAIL B
MOLD CMPDEXPOSED Cu
ALTERNATE
CONSTRUCTION
DETAIL B
DETAIL A
A0.10 BC
0.05
C
A0.10 BC
M
M
M
SOLDERING FOOTPRINT
DIMENSIONS: MILLIMETERS
3.64
5.30
5.30
0.40
0.63
0.25
40X
40X
PITCH
PKG
OUTLINE
1
3.64
RECOMMENDED
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSIONS: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30mm FROM THE TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
DIM MIN MAX
MILLIMETERS
A 0.80 1.00
A1 −− 0.05
A3 0.20 REF
b 0.15 0.25
D 5.00 BSC
D2 3.40 3.60
E 5.00 BSC
3.60E2 3.40
e 0.40 BSC
L 0.30 0.50
L1 −−− 0.15
A0.10 BC
M
e/2
L2
DETAIL A
L2 0.12 REF
L2
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage
may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer
is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of
any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and
do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized
for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices
intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and
hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was
negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright
laws and is not for resale in any manner.
P
UBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
NCP81274/D
NVIDIA is a registered trademark of of NVIDIA Corporation in the U.S. and/or other countries. All other brand names and product names appearing in this documen
t
are registered trademarks or trademarks of their respective holders.
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
al
Sales Representative

NCP81274MNTXG

Mfr. #:
Manufacturer:
ON Semiconductor
Description:
Motor / Motion / Ignition Controllers & Drivers 8 PHASE CONTROLLER
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet