OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TDA9899HN/V2,518

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P51P52-P54P55-P57P58-P60P61-P63P64-P66P67-P69P70-P72P73-P75P76-P78P79-P81P82-P84P85-P87P88-P90P91-P93P94-P96P97-P99P100-P102P103-P103
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 37 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
Power-on reset
V
P(POR)
power-on reset supply
voltage
for start of reset at
decreasing supply voltage
[2]
2.5 3.0 3.5 V
for end of reset at
increasing supply voltage;
I
2
C-bus transmission
enable
[2]
- 3.3 4.4 V
VIF amplifier; pins IF1A, IF1B, IF2A and IF2B
V
I
input voltage - 1.95 - V
R
i(dif)
differential input resistance
[3]
-2-kΩ
C
i(dif)
differential input capacitance
[3]
-3-pF
V
i(IF)(RMS)
RMS IF input voltage lower limit at −1 dB video
output signal
- 60 100 µV
upper limit at +1 dB video
output signal
150 190 - mV
permissible overload
[4]
- - 320 mV
∆G
IF
IF gain variation difference between
picture and sound carrier;
within AGC range;
∆f = 5.5 MHz
- 0.7 - dB
G
VIF(cr)
control range VIF gain 60 66 - dB
f
−3dB(VIF)l
lower VIF cut-off frequency - 15 - MHz
f
−3dB(VIF)u
upper VIF cut-off frequency - 80 - MHz
FPLL and true synchronous video demodulator
[5]
V
LFVIF
voltage on pin LFVIF (DC) 0.9 - 3.6 V
f
VCO(max)
maximum VCO frequency f
VCO
=2f
PC
120 140 - MHz
f
VIF
VIF frequency see Table 26 ---MHz
∆f
VIF(dah)
digital acquisition help VIF
frequency window
related to f
VIF
all standards except
M/N
- ±2.3 - MHz
M/N standard - ±1.8 - MHz
t
acq
acquisition time B
LF(−3dB)
=70kHz
[6]
--30ms
V
lock(min)(RMS)
RMS minimum lock-in
voltage
measured on pins IF1A
and IF1B or IF2A and
IF2B; maximum IF gain;
negative modulation
mode W2[7] = 1 and PLL
set to overmodulation
mode W2[2] = 0 and
W2[1] = 0
-3070µV
Table 55. Characteristics
…continued
V
P
=5V; T
amb
=25
°
C; see Table 26 for input frequencies; B/G standard is used for the specification (f
PC
= 38.375 MHz;
f
SC
= 32.875 MHz; PC / SC = 13 dB; f
AF
= 400 Hz); input level V
i(IF)
= 10 mV (RMS) (sync level for B/G; peak white level
for L); IF input from 50
Ω
via broadband transformer 1 : 1; video modulation: Vestigial SideBand (VSB); residual carrier for
B/G is 10 % and for L is 3 %; video signal in accordance with “ITU-T J.63 line 17 and line 330” or “NTC-7 Composite”;
internal Nyquist slope switched on (W7[0] = 0); not dual mode; measurements taken in test circuit of
Figure 49; unless
otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 38 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
T
cy(dah)
digital acquisition help cycle
time
-64-µs
t
w(dah)
digital acquisition help pulse
width
64 - - µs
I
pul(acq)VIF
VIF acquisition pulse current sink or source 21 - 33 µA
K
O(VIF)
VIF VCO steepness ∆f
VIF
/ ∆V
LFVIF
- 26 - MHz/V
K
D(VIF)
VIF phase detector
steepness
∆I
VPLL
/ ∆ϕ
VCO(VIF)
-23-µA/rad
I
offset(VIF)
VIF offset current −10 +1µA
Video output 2 V; pin CVBS
[7]
Normal mode (sound carrier trap active) and sound carrier on
V
o(video)(p-p)
peak-to-peak video output
voltage
positive or negative
modulation; see
Figure 8
W4[7] = 0; W7[4] = 0 1.7 2.0 2.3 V
W4[7] = 1; W7[4] = 0 1.7 2.0 2.3 V
W4[7] = 0; W7[4] = 1 1.7 2.0 2.3 V
W4[7] = 1; W7[4] = 1 - 2.0 - V
∆V
o(CVBS)
CVBS output voltage
difference
difference between
L and B/G standard
W4[7] = 0; W7[4] = 0 −240 - +240 mV
W4[7] = 1; W7[4] = 0 −240 - +240 mV
W4[7] = 0; W7[4] = 1 −240 - +240 mV
V
video
/V
sync
video voltage to sync voltage
ratio
2.0 2.33 2.75
V
syncl
sync level voltage W4[7] = 0; W7[4] = 0 1.0 1.2 1.4 V
W4[7] = 1; W7[4] = 0 0.9 1.2 1.5 V
W4[7] = 0; W7[4] = 1 0.9 1.2 1.5 V
V
clip(video)u
upper video clipping voltage V
P
− 1.2 V
P
− 1- V
V
clip(video)l
lower video clipping voltage - 0.4 0.9 V
R
O
output resistance
[3]
--30Ω
I
bias(int)
internal bias current (DC) for emitter-follower 1.5 2.0 - mA
I
sink(o)(max)
maximum output sink current AC and DC 1 - - mA
I
source(o)(max)
maximum output source
current
AC and DC 3.9 - - mA
∆V
o(CVBS)
CVBS output voltage
difference
50 dB gain control - - 0.5 dB
30 dB gain control - - 0.1 dB
∆V
blt
/V
CVBS
black level tilt to CVBS
voltage ratio
negative modulation - - 1 %
Table 55. Characteristics
…continued
V
P
=5V; T
amb
=25
°
C; see Table 26 for input frequencies; B/G standard is used for the specification (f
PC
= 38.375 MHz;
f
SC
= 32.875 MHz; PC / SC = 13 dB; f
AF
= 400 Hz); input level V
i(IF)
= 10 mV (RMS) (sync level for B/G; peak white level
for L); IF input from 50
Ω
via broadband transformer 1 : 1; video modulation: Vestigial SideBand (VSB); residual carrier for
B/G is 10 % and for L is 3 %; video signal in accordance with “ITU-T J.63 line 17 and line 330” or “NTC-7 Composite”;
internal Nyquist slope switched on (W7[0] = 0); not dual mode; measurements taken in test circuit of
Figure 49; unless
otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 39 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
∆V
blt(v)
/V
CVBS
vertical black level tilt to
CVBS voltage ratio
worst case in L standard;
vision carrier modulated
by test line [Vertical
Interval Test Signal
(VITS)] only
--3%
G
dif
differential gain
“ITU-T J.63 line 330”
[8]
B/G standard - - 5 %
L standard - - 7 %
ϕ
dif
differential phase
“ITU-T J.63 line 330”
[8]
B/G standard - 2 4 deg
L standard - 2 4 deg
(S/N)
w
weighted signal-to-noise ratio B/G standard; 50 % grey
video signal; unified
weighting filter
(
“ITU-T J.61”
);
see
Figure 19
[9]
53 57 - dB
(S/N)
unw
unweighted signal-to-noise
ratio
M/N standard; 50 IRE
grey video signal;
see
Figure 19
47 51 - dB
V
PC(rsd)(RMS)
RMS residual picture carrier
voltage
fundamental wave and
harmonics
- 25mV
∆f
PC(p-p)
peak-to-peak picture carrier
frequency variation
3 % residual carrier;
50 % serration pulses;
L standard
[3]
--12kHz
∆ϕ phase difference 0 % residual carrier;
50 % serration pulses;
L standard;
L-gating = 0 %
[3]
--3%
α
H(video)
video harmonics suppression AC load: C
L
<20pF,
R
L
>1kΩ
[10]
35 40 - dB
α
sp
spurious suppression
[11]
40--dB
PSRR
CVBS
power supply ripple rejection
on pin CVBS
f
ripple
=70Hz;
video signal; grey level;
positive and negative
modulation; see
Figure 9
14 20 - dB
M/N standard inclusive Korea; see
Figure 20
[12]
α
ripple(resp)f
frequency response ripple 0.5 MHz to 2.5 MHz −1 - +1 dB
2.5 MHz to 3.6 MHz −2 - +2 dB
3.6 MHz to 3.8 MHz −3 - +2 dB
3.8 MHz to 4.2 MHz −16 - +2 dB
α
SC1
first sound carrier attenuation f = f
SC1
= 4.5 MHz 38 - - dB
f=f
SC1
± 60 kHz 29 - - dB
Table 55. Characteristics
…continued
V
P
=5V; T
amb
=25
°
C; see Table 26 for input frequencies; B/G standard is used for the specification (f
PC
= 38.375 MHz;
f
SC
= 32.875 MHz; PC / SC = 13 dB; f
AF
= 400 Hz); input level V
i(IF)
= 10 mV (RMS) (sync level for B/G; peak white level
for L); IF input from 50
Ω
via broadband transformer 1 : 1; video modulation: Vestigial SideBand (VSB); residual carrier for
B/G is 10 % and for L is 3 %; video signal in accordance with “ITU-T J.63 line 17 and line 330” or “NTC-7 Composite”;
internal Nyquist slope switched on (W7[0] = 0); not dual mode; measurements taken in test circuit of
Figure 49; unless
otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P51P52-P54P55-P57P58-P60P61-P63P64-P66P67-P69P70-P72P73-P75P76-P78P79-P81P82-P84P85-P87P88-P90P91-P93P94-P96P97-P99P100-P102P103-P103

TDA9899HN/V2,518

Mfr. #:
Buy TDA9899HN/V2,518
Manufacturer:
NXP Semiconductors
Description:
Up-Down Converters TDA9899HN/HVQFN48//V2/REEL 13 Q1 DP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet