TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 4 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
V
o(video)(p-p)
peak-to-peak video output voltage see Figure 8
positive or negative
modulation; normal mode
and sound carrier on
[2]
1.7 2.0 2.3 V
trap bypass mode and
sound carrier off
[3]
- 1.1 - V
G
dif
differential gain
“ITU-T J.63 line 330”
[2][4]
B/G standard - - 5 %
L standard - - 7 %
ϕ
dif
differential phase
“ITU-T J.63 line 330”
[2][4]
B/G standard - 2 4 deg
L standard - 2 4 deg
B
video(3dB)
3 dB video bandwidth trap bypass mode and
sound carrier off; AC load:
C
L
<20pF, R
L
>1k
[3]
68- MHz
α
SC1
first sound carrier attenuation M/N standard;
f=f
SC1
= 4.5 MHz;
see
Figure 20
[3]
38--dB
B/G standard;
f=f
SC1
= 5.5 MHz;
see
Figure 22
[3]
35--dB
(S/N)
w
weighted signal-to-noise ratio normal mode and sound
carrier on; B/G standard;
50 % grey video signal;
unified weighting filter
(
“ITU-T J.61”
);
see
Figure 19
[2][5]
53 57 - dB
PSRR
CVBS
power supply ripple rejection on
pin CVBS
normal mode and sound
carrier on; f
ripple
=70Hz;
video signal; grey level;
positive and negative
modulation; see
Figure 9
[2]
14 20 - dB
I
AFC
/f
VIF
change of AFC current with VIF
frequency
AFC TV mode
[6]
0.85 1.05 1.25 µA/kHz
Audio part
V
o(AF)(RMS)
RMS AF output voltage FM: QSS or TSS mode;
27 kHz FM deviation;
50 µs de-emphasis
430 540 650 mV
AM: 54 % modulation 400 500 600 mV
THD total harmonic distortion FM: 50 µs de-emphasis;
FM deviation: for TV mode
27 kHz and for radio mode
22.5 kHz
- 0.15 0.50 %
AM: 54 % modulation;
BP on; see
Figure 32
- 0.5 1.0 %
Table 1. Quick reference data
…continued
V
P
=5V; T
amb
=25
°
C.
Symbol Parameter Conditions Min Typ Max Unit
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 5 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
f
3dB(AF)
AF cut-off frequency W3[2] = 0; W3[4] = 0;
without de-emphasis;
FM window
width = 237.5 kHz
80 100 - kHz
(S/N)
w(AF)
AF weighted signal-to-noise ratio
“ITU-R BS.468-4”
FM: 27 kHz FM deviation;
50 µs de-emphasis; vision
carrier unmodulated;
FM PLL only
48 56 - dB
AM: BP off 44 50 - dB
PSRR power supply ripple rejection f
ripple
= 70 Hz; see Figure 9 14 20 - dB
V
o(RMS)
RMS output voltage IF intercarrier single-ended
to GND; SC1 on; SC2 off
90 140 180 mV
IF intercarrier single-ended
to GND; L standard;
without modulation; BP on;
W7[5] = 0
45 70 90 mV
FM sound part
V
i(FM)(RMS)
RMS FM input voltage gain controlled operation;
W1[1:0] = 10 or
W1[1:0] = 11 or
W1[1:0] = 01; see
Figure 14
2 - 300 mV
I
AFC
/f
RIF
change of AFC current with RIF
frequency
AFC radio mode
[6]
0.85 1.05 1.25 µA/kHz
α
AM
AM suppression referenced to 27 kHz
FM deviation;
50 µs de-emphasis;
AM: f = 1 kHz; m = 54 %
35 46 - dB
Digital TV signal processing
Digital direct IF
V
o(dif)(p-p)
peak-to-peak differential output
voltage
between pin OUT2A and
pin OUT2B
[7]
W4[7] = 0 - 1.0 1.1 V
W4[7] = 1 - 0.50 0.55 V
G
IF(max)
maximum IF gain output peak-to-peak level to
input RMS level ratio
[8]
-83-dB
G
IF(cr)
control range IF gain
[8]
60 66 - dB
PSRR power supply ripple rejection residual spurious at nominal
differential output voltage
dependent on power supply
ripple
[8]
f
ripple
=70Hz - 60 - dB
f
ripple
= 20 kHz - 60 - dB
Digital low IF
V
o(dif)(p-p)
peak-to-peak differential output
voltage
between pin OUT1A and
pin OUT1B; W4[7] = 0
[7]
-2-V
Table 1. Quick reference data
…continued
V
P
=5V; T
amb
=25
°
C.
Symbol Parameter Conditions Min Typ Max Unit
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 6 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
[1] Values of video and sound parameters can be decreased at V
P
= 4.5 V.
[2] AC load; C
L
< 20 pF and R
L
>1k. The sound carrier frequencies (depending on TV standard) are attenuated by the integrated sound
carrier traps.
[3] The sound carrier trap can be bypassed by setting the I
2
C-bus bit W2[0] to logic 0; see Table 25. In this way the full composite video
spectrum appears at pin CVBS. The video amplitude is reduced to 1.1 V (p-p).
G
IF(max)
maximum IF gain output peak-to-peak level to
input RMS level ratio
[8]
-89-dB
G
IF(cr)
control range IF gain
[8]
60 66 - dB
f
synth
synthesizer frequency see Table 37 and Table 38 ---MHz
ϕ
n(synth)
synthesizer phase noise with 4 MHz crystal oscillator
reference; f
synth
= 31 MHz;
f
IF
=36MHz
at 1 kHz
[8]
89 99 - dBc/Hz
at 10 kHz
[8]
89 99 - dBc/Hz
at 100 kHz
[8]
98 102 - dBc/Hz
at 1.4 MHz
[8]
115 119 - dBc/Hz
α
ripple(pb)LIF
low IF pass-band ripple 6 MHz bandwidth - - 2.7 dB
7 MHz bandwidth - - 2.7 dB
8 MHz bandwidth - - 2.7 dB
α
stpb
stop-band attenuation 8 MHz band; f = 15.75 MHz 30 40 - dB
α
image
image rejection 10 MHz to 0 MHz; BP on 30 34 - dB
C/N carrier-to-noise ratio at f
o
= 4.9 MHz;
V
i(IF)
= 10 mV (RMS);
see
Figure 38
[8][9][10]
112 118 - dBc/Hz
Digital zero IF
V
o(dif)(p-p)
peak-to-peak differential output
voltage
between pin OUT1A and
pin OUT1B or between
pin OUT2A and pin OUT2B;
W4[7] = 0
[7]
-2-V
G
IF(max)
maximum IF gain output peak-to-peak level to
input RMS level ratio
[8]
-89-dB
G
IF(cr)
control range IF gain
[8]
60 66 - dB
f
synth
synthesizer frequency see Table 37 and Table 38 ---MHz
ϕ
n(synth)
synthesizer phase noise with 4 MHz crystal oscillator
reference; f
synth
= 31 MHz;
f
IF
=36MHz
at 1 kHz
[8]
89 99 - dBc/Hz
at 10 kHz
[8]
89 99 - dBc/Hz
at 100 kHz
[8]
98 102 - dBc/Hz
at 1.4 MHz
[8]
115 119 - dBc/Hz
Reference frequency input from external source
f
ref
reference frequency W7[7] = 0
[11]
-4-MHz
V
ref(RMS)
RMS reference voltage W7[7] = 0; see Figure 35
and
Figure 47
15 150 500 mV
Table 1. Quick reference data
…continued
V
P
=5V; T
amb
=25
°
C.
Symbol Parameter Conditions Min Typ Max Unit

TDA9899HN/V2,518

Mfr. #:
Manufacturer:
NXP Semiconductors
Description:
Up-Down Converters TDA9899HN/HVQFN48//V2/REEL 13 Q1 DP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union