OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TDA9899HN/V2,518

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P51P52-P54P55-P57P58-P60P61-P63P64-P66P67-P69P70-P72P73-P75P76-P78P79-P81P82-P84P85-P87P88-P90P91-P93P94-P96P97-P99P100-P102P103-P103
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 43 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
I
sink(o)
output sink current W7[3] = 0 - - 3 mA
W7[3] = 1 - - 10 µA
V
OH
HIGH-level output voltage - - V
P
+ 0.5 V
VIF AGC; pin CIFAGC
I
ch(max)
maximum charge current L standard 75 100 125 µA
I
ch(add)
additional charge current L standard: in the event of
missing VITS pulses and
no white video content
- 100 - nA
I
dch
discharge current L standard; normal mode - 35 - nA
L standard; fast mode - 1.8 - µA
VIF AGC control; pin AGCVIN
I
sink(i)(max)
maximum input sink current
[3]
--1µA
I
source(i)(max)
maximum input source
current
[3]
--1µA
V
i(max)
maximum input voltage
[3]
--V
P
V
V
AGCVIN
voltage on pin AGCVIN
[3]
1 - 3.5 V
∆G
VIF
/∆V
AGCVIN
change of VIF gain with
voltage on pin AGCVIN
V
AGCVIN
= 2.8 V - −75 - dB/V
Tuner AGC; pin TAGC
Integral TAGC loop mode (W6[7:6] = 10); TAGC is current output; applicable for negative modulation only; unmodulated VIF;
see
Table 48 and Figure 12
V
i(IF)(RMS)
RMS IF input voltage at starting point of tuner
AGC takeover;
I
sink(TAGC)
= 100 µA
W9[4:0] = 0 0000 - 57.9 - dBµV
W9[4:0] = 1 0000 - 78.7 - dBµV
W9[4:0] = 1 1111 - 98.2 - dBµV
α
acc(set)TOP
TOP setting accuracy −2 - +2 dB
I
source
source current TAGC charge current
normal mode 0.20 0.27 0.34 µA
fast mode activated by
internal level detector
71013µA
I
sink
sink current TAGC discharge current;
V
TAGC
=1V
400 500 600 µA
∆α
acc(set)TOP
/∆T TOP setting accuracy
variation with temperature
W9[4:0] = 1 0000 - - 0.02 dB/K
R
L
load resistance
[3]
50--MΩ
V
sat(u)
upper saturation voltage pin operating as current
output
V
P
− 0.3 - - V
Table 55. Characteristics
…continued
V
P
=5V; T
amb
=25
°
C; see Table 26 for input frequencies; B/G standard is used for the specification (f
PC
= 38.375 MHz;
f
SC
= 32.875 MHz; PC / SC = 13 dB; f
AF
= 400 Hz); input level V
i(IF)
= 10 mV (RMS) (sync level for B/G; peak white level
for L); IF input from 50
Ω
via broadband transformer 1 : 1; video modulation: Vestigial SideBand (VSB); residual carrier for
B/G is 10 % and for L is 3 %; video signal in accordance with “ITU-T J.63 line 17 and line 330” or “NTC-7 Composite”;
internal Nyquist slope switched on (W7[0] = 0); not dual mode; measurements taken in test circuit of
Figure 49; unless
otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 44 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
V
sat(l)
lower saturation voltage pin operating as current
output
- - 0.3 V
α
th(fast)AGC
AGC fast mode threshold activated by internal fast
AGC detector; I
2
C-bus
setting corresponds to
W9[4:0] = 1 0000
[3]
6810dB
t
d
delay time before activating; V
i(IF)
below α
th(fast)AGC
40 60 80 ms
TAGC loop based on VIF AGC (W6[7:6] = 11); TAGC is voltage output; applicable for TV mode: positive modulation and
optional for negative modulation); see
Table 51; Figure 12 and Figure 13
V
i(IF)(RMS)
RMS IF input voltage at starting point of tuner
AGC takeover;
V
TAGC
= 3.5 V
R
TOP2
=22kΩ or
W10[5:0] = 00 0000
-61-dBµV
R
TOP2
=10kΩ or
W10[5:0] = 01 0000
-81-dBµV
R
TOP2
=0kΩ -96-dBµV
W10[5:0] = 01 1111 - 99 - dBµV
α
acc(set)TOP2
TOP2 setting accuracy −6 - +6 dB
∆α
acc(set)TOP2
/∆T TOP2 setting accuracy
variation with temperature
V
TAGC
= 3.5 V - 0.03 0.07 dB/K
V
O
output voltage no tuner gain reduction 4.5 - V
P
V
maximum tuner gain
reduction
0.2 - 0.6 V
∆G
slip(TAGC)
TAGC slip gain offset tuner gain voltage from
0.6 V to 3.5 V
358dB
TOP adjust 2; pin TOP2; IF based TAGC loop mode; see
Figure 13
V
TOP2
voltage on pin TOP2 (DC) pin open-circuit - 3.5 - V
R
I
input resistance - 27 - kΩ
R
TOP2
resistance on pin TOP2 adjustment of VIF AGC
based TAGC loop
W10[5] = 1; external
resistor operation
0 - 22 kΩ
W10[5] = 0; forced
I
2
C-bus operation
100 - - kΩ
Table 55. Characteristics
…continued
V
P
=5V; T
amb
=25
°
C; see Table 26 for input frequencies; B/G standard is used for the specification (f
PC
= 38.375 MHz;
f
SC
= 32.875 MHz; PC / SC = 13 dB; f
AF
= 400 Hz); input level V
i(IF)
= 10 mV (RMS) (sync level for B/G; peak white level
for L); IF input from 50
Ω
via broadband transformer 1 : 1; video modulation: Vestigial SideBand (VSB); residual carrier for
B/G is 10 % and for L is 3 %; video signal in accordance with “ITU-T J.63 line 17 and line 330” or “NTC-7 Composite”;
internal Nyquist slope switched on (W7[0] = 0); not dual mode; measurements taken in test circuit of
Figure 49; unless
otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
TDA9899_3 © NXP B.V. 2008. All rights reserved.
Product data sheet Rev. 03 — 15 January 2008 45 of 103
NXP Semiconductors
TDA9899
Multistandard hybrid IF processing including car mobile
AGC switch; pin AGCSWI
V
AGCSWI
voltage on pin AGCSWI (DC) pin open-circuit - 0 - V
LOW-level input voltage;
see
Table 34
--1V
HIGH-level input voltage;
see
Table 34
2--V
R
I
input resistance - 50 - kΩ
Pin CTAGC
V
CTAGC
voltage on pin CTAGC
[3]
0.2 - 0.55V
P
V
I
L
leakage current sink
[3]
--10nA
source
[3]
--10nA
Control current or voltage monitor output; pin MPP2
General
V
sat(u)
upper saturation voltage V
P
− 0.8 V
P
− 0.5 - V
V
sat(l)
lower saturation voltage - 0.5 0.8 V
AFC (current output)
I
o
output current sink or source;
see
Figure 16 and
Figure 17
[15][16]
100 kHz VIF deviation 80 - 160 µA
200 kHz VIF deviation 160 200 240 µA
1.5 MHz VIF deviation 160 - 240 µA
AFC TV mode
∆I
AFC
/∆f
VIF
change of AFC current with
VIF frequency
[16]
0.85 1.05 1.25 µA/kHz
f
VIFacc(dig)
digital accuracy of VIF
frequency
read-out via I
2
C-bus;
R1[4:1] = f
0
; f
ref
= 4 MHz
[17]
−20 - +20 kHz
f
VIFacc(a)
analog accuracy of VIF
frequency
I
AFC
= 0 A; f
ref
= 4 MHz
[17]
−20 - +20 kHz
AFC radio mode
∆I
AFC
/∆f
RIF
change of AFC current with
RIF frequency
[16]
0.85 1.05 1.25 µA/kHz
f
RIFacc(dig)
digital accuracy of RIF
frequency
read-out via I
2
C-bus;
R1[4:1] = f
0
; f
ref
= 4 MHz
[17]
−10 - +10 kHz
f
RIFacc(a)
analog accuracy of RIF
frequency
I
AFC
= 0 A; f
ref
= 4 MHz
[17]
−10 - +10 kHz
Table 55. Characteristics
…continued
V
P
=5V; T
amb
=25
°
C; see Table 26 for input frequencies; B/G standard is used for the specification (f
PC
= 38.375 MHz;
f
SC
= 32.875 MHz; PC / SC = 13 dB; f
AF
= 400 Hz); input level V
i(IF)
= 10 mV (RMS) (sync level for B/G; peak white level
for L); IF input from 50
Ω
via broadband transformer 1 : 1; video modulation: Vestigial SideBand (VSB); residual carrier for
B/G is 10 % and for L is 3 %; video signal in accordance with “ITU-T J.63 line 17 and line 330” or “NTC-7 Composite”;
internal Nyquist slope switched on (W7[0] = 0); not dual mode; measurements taken in test circuit of
Figure 49; unless
otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P51P52-P54P55-P57P58-P60P61-P63P64-P66P67-P69P70-P72P73-P75P76-P78P79-P81P82-P84P85-P87P88-P90P91-P93P94-P96P97-P99P100-P102P103-P103

TDA9899HN/V2,518

Mfr. #:
Buy TDA9899HN/V2,518
Manufacturer:
NXP Semiconductors
Description:
Up-Down Converters TDA9899HN/HVQFN48//V2/REEL 13 Q1 DP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet