10©2018 Integrated Device Technology, Inc. March 15, 2018
5P49V6965 Datasheet
1
Guaranteed by design and characterization. Not 100% tested in production.
2
Measured from differential waveform.
3
Slew rate is measured through the V
SWING
voltage range centered around differential 0V. This results in a ±150mV window around differential 0V.
4
V
CROSS
is defined as voltage where Clock = Clock# measured on a component test board and only applies to the differential rising edge (i.e. Clock
rising and Clock# falling).
5
The total variation of all V
CROSS
measurements in any particular system. Note that this is a subset of V
CROSS
min/max (V
CROSS
absolute) allowed.
The intent is to limit V
CROSS
induced modulation by setting ΔV
CROSS
to be smaller than V
CROSS
absolute.
6
Measured from single-ended waveform.
Table 11. Electrical Characteristics – LVPECL Outputs
V
DDA
, V
DDD
, V
DDO0
= 3.3V ±5%, 2.5V ±5%, T
A
= -40°C to +85°C unless stated otherwise.
Symbol Parameter Minimum Typical Maximum Units
V
OH
Output Voltage High, Terminated through 50 tied to V
DD
- 2V V
DDO
- 1.19 V
DDO
- 0.69 V
V
OL
Output Voltage Low, Terminated through 50 tied to V
DD
- 2V V
DDO
- 1.94 V
DDO
- 1.4 V
V
SWING
Peak-to-Peak Output Voltage Swing 0.55 0.993 V
T
R
LVPECL rise time 20%–80% 400 ps
T
F
LVPECL fall time 80%–20% 400 ps
Table 12. Electrical Characteristics – HCSL Outputs
1
V
DDA
, V
DDD
, V
DDO0
= 3.3V ±5%, 2.5V ±5%, T
A
= -40°C to +85°C unless stated otherwise.
Symbol Parameter Conditions Minimum Typical Maximum Units
dV/dt Slew Rate Scope averaging on
2,3
.14V/ns
ΔdV/dt Slew Rate Matching Scope averaging on
2,3
.20%
V
MAX
Maximum Voltage
Measurement on single-ended signal using
absolute value (scope averaging off).
1150 mV
V
MIN
Minimum Voltage -300 mV
V
SWING
Voltage Swing Scope averaging off
2,6
.300mV
V
CROSS
Crossing Voltage Value Scope averaging off
4,6
. 250 550 mV
ΔV
CROSS
Crossing Voltage Variation Scope averaging off
5
.140mV
Table 13. Spread Spectrum Generation Specifications
Symbol Parameter Conditions Minimum Typical Maximum Units
f
SSOUT
Spread Frequency Output frequency range for spread spectrum. 5 300 MHz
f
MOD
Mod Frequency Modulation frequency. 30 to 63 kHz
f
SPREAD
Spread Value
Amount of spread value (programmable)–center spread. ±0.25% to ±2.5%
%f
OUT
Amount of spread value (programmable)–down spread. -0.5% to -5%
11©2018 Integrated Device Technology, Inc. March 15, 2018
5P49V6965 Datasheet
I
2
C Bus Characteristics
1
A device must internally provide a hold time of at least 300ns for the SDA signal (referred to the V
IH(MIN)
of the SCL signal) to bridge the undefined
region of the falling edge of SCL.
2
I
2
C inputs are 5V tolerant.
Table 14. I
2
C Bus DC Characteristics
Symbol Parameter Conditions Minimum Typical Maximum Units
V
IH
Input High Level
For SEL1/SDA pin and
SEL0/SCL pin.
0.7 x V
DDD
V
V
IL
Input Low Level
For SEL1/SDA pin and
SEL0/SCL pin.
0.3 x V
DDD
V
V
HYS
Hysteresis of Inputs 0.05 x V
DDD
V
I
IN
Input Leakage Current -1 30 μA
V
OL
Output Low Voltage I
OL
= 3mA. 0.4 V
Table 15. I
2
C Bus AC Characteristics
Symbol Parameter Conditions Minimum Typical Maximum Units
F
SCLK
Serial Clock Frequency (SCL) 10 400 kHz
t
BUF
Bus Free Time between Stop and Start 1.3 μs
t
SU:START
Setup Time, Start 0.6 μs
t
HD:START
Hold Time, Start 0.6 μs
t
SU:DATA
Setup Time, Data Input (SDA) 0.1 μs
t
HD:DATA
Hold Time, Data Input (SDA)
1
0 μs
t
OVD
Output Data Valid from Clock 0.9 μs
C
B
Capacitive Load for Each Bus Line 400 pF
t
R
Rise Time, Data and Clock (SDA, SCL) 20 + 0.1 x C
B
300 ns
t
F
Fall Time, Data and Clock (SDA, SCL) 20 + 0.1 x C
B
300 ns
t
HIGH
High Time, Clock (SCL) 0.6 μs
t
LOW
Low Time, Clock (SCL) 1.3 μs
t
SU:STOP
Setup Time, Stop 0.6 μs
12©2018 Integrated Device Technology, Inc. March 15, 2018
5P49V6965 Datasheet
Test Loads
Figure 2. LVCMOS Test Load
Figure 3. HCSL Test Load
Figure 4. LVDS Test Load
Figure 5. LVPECL Test Load
2pF
Differential
Zo = 100 Ohm
33 Ohm
Device
33 Ohm
50 Ohm
2pF
50 Ohm
Test
Points
Differential
Zo = 100 Ohm
100 Ohm
Test
Points
Device
2pF
2pF
Differential
Zo = 100 Ohm
Test
Points
Device
50Ohm 50 Ohm
R
2pF2pF
R = 50 Ohm for 3.3V LVPECL
R = 18 Ohm for 2.5V LVPECL

5P49V6965A000NLGI

Mfr. #:
Manufacturer:
IDT
Description:
Clock Generators & Support Products VersaClock 6E Standard Part
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet