1©2017 Integrated Device Technology, Inc December 18, 2017
Description
The 5X2503 MicroClock is a programmable clock generator and is
intended for low-power, consumer, wearable and smart devices.
The 5X2503 device is a 3 PLL architecture design. Each PLL is
individually programmable, allowing for up to 3 unique frequency
outputs. The 5X2503 has built-in unique features such as Proactive
Power Saving (PPS) to deliver better system-level power
management.
An internal OTP memory allows the user to store the configuration in
the device without programming after power up. It can then be
reprogrammed again through the I
2
C interface.
The device has programmable VCO and PLL source selection
allowing the user to do power-performance optimization based on
the application requirements. A low-power 32.768kHz clock is
supported with only less than 2μA current consumption for system
RTC reference clock needs.
Typical Applications
SmartDevice, Handheld, Wearable applications
Consumer application crystal replacement
Features
Configurable OE1 pin function as OE, PPS or DFC control
function
PPS: Proactive Power Saving features save power during the end
device power-down mode
DFC: Dynamic Frequency Control feature allows programming up
to 4 difference frequencies that switch dynamically
Integrated 26MHz crystal; no external input source requirement
Spread spectrum clock support to lower system EMI
I
2
C Interface
Output Features
3 LVCMOS outputs, 1MHz–125MHz
Low-power 32.768kHz clock supported
Wireless clock crystal integration and fan-out directly
Key Specifications
2μA operation for RTC clock 32.768kHz output
2.5 × 2.5 mm 12-DFN with crystal integration; small-form-factor
package
Block Diagram
Overshoot Reduction
(ORT)
OSC
PLL2
OUT3
OUT2
OUT1
PLL3
OE1
SDA_DFC0/OE2
SEL_DFC/ SCL_DFC1/OE3
OTP memory (1 configuration ) Proactive Power Saving Logic (PPS)
I
2
C Engine
VDDOUT1
Dynamic Frequency Control Logic (DFC)
POR
Power
Monitor
VDD1_8
32.768K
DCO
Calibration
VSS
VDDOUT2
PLL1
VSS
VSS
Mux
&
Divider
5X2503
Datasheet
MicroClock Programmable Clock
Generator
2©2017 Integrated Device Technology, Inc December 18, 2017
5X2503 Datasheet
Power Group
Output Source Selection Register Setting Tables
Power Supply SE DIV MUX PLL DCO Xtal
V
DDOUT1
OUT1—————
V
DDOUT2
OUT2/OUT3 V
V
DD1_8
VVVV
OUT3 Source B35b7 B35b6
Divider 3 (DIV3) 0 0
Divider 5 (DIV5) 0 1
Divider 1 (DIV1) 1 0
32.768kHz DCO 1 1
OUT2 Source B35b5 B35b4
Divider 3 (DIV3) 0 0
Divider 5 (DIV5) 0 1
Divider 1 (DIV1) 1 0
32.768kHz DCO 1 1
OUT2 Source B35b3 B35b2
Divider 3 (DIV3) 0 0
Divider 5 (DIV5) 0 1
Divider 1 (DIV1) 1 0
32.768kHz DCO 1 1
DIV1 Source B35b7 B35b6
PLL1 0 0
DIV4 seed 1 X
3©2017 Integrated Device Technology, Inc December 18, 2017
5X2503 Datasheet
Pin Assignments
Figure 1. Pin Assignments for 2.5 × 2.5 mm 12-DFN Package
Pin Descriptions
Device Feature and Function
DFC – Dynamic Frequency Control
OTP programmable–4 different feedback fractional dividers (4 VCO frequencies) that apply to PLL2.
ORT (overshoot reduction) function will be applied automatically during the VCO frequency change.
Smooth frequency incremental or decremental from current VCO to targeted VCO base on DFC hardware pins selection.
Table 1. Pin Descriptions
Number Name Type Description
1 SDA_DFC0/OE2 I/O I
2
C data pin; can be DFC0 function by OTP programming or selected by
SEL_DFC at power-on default. Output enable pin for OUT2.
2 SEL_DFC/SCL_DFC1/OE3 Input I
2
C clock pin; can be DFC1 function by OTP programming selected by
SEL_DFC at power-on default. Output enable pin for OUT3.
3V
SS
Power Ground pin.
4V
SS
Power Ground pin.
5V
DD1_8
Power 1.8V power rail.
6V
DDOUT1
Power 1.2V / 1.8V output clock power supply pin; supports OUT1.
7 OUT1 Output 1.2V / 1.8V LVCMOS clock output.
8 OE1 Input Output enable control 1.
9 OUT2 Output 1.8V LVCMOS clock output.
10 V
DDOUT2
Power 1.8V output clock power supply pin; supports OUT2/3.
11 OUT3 Output 1.8V LVCMOS clock output.
12 V
SS
Power Ground pin.
EPAD GND Connect to ground pad.
OE1
OUT2
V
DDOUT2
OUT3
V
SS
OUT1
V
DD1_8
V
SS
V
SS
SEL_DFC/SCL_DFC1/OE3
SDA_DFC0/OE2
V
DDOUT1
1
2
3
4
5
6
12
11
10
9
8
7
2.5 × 2.5 mm 12-DFN

5X2503-000NDGI

Mfr. #:
Manufacturer:
IDT
Description:
Clock Generators & Support Products Microclock Programmable Clock Generator
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet