LTC2282
5
2282fb
POWER REQUIREMENTS
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
DD
Analog Supply Voltage (Note 9)
l
2.85 3 3.4 V
OV
DD
Output Supply Voltage (Note 9)
l
0.5 3 3.6 V
IV
DD
Supply Current Both ADCs at f
S(MAX)
l
180 210 mA
P
DISS
Power Dissipation Both ADCs at f
S(MAX)
l
540 630 mW
P
SHDN
Shutdown Power (Each Channel) SHDN = H, OE = H, No CLK 2 mW
P
NAP
Nap Mode Power (Each Channel) SHDN = H, OE = L, No CLK 15 mW
TIMING CHARACTERISTICS
The l denotes the specifi cations which apply over the full operating temperature
range, otherwise specifi cations are at T
A
= 25°C. (Note 4)
The ● denotes the specifi cations which apply over the full operating temperature
range, otherwise specifi cations are at T
A
= 25°C. (Note 8)
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
f
s
Sampling Frequency (Note 9)
l
1 105 MHz
t
L
CLK Low Time Duty Cycle Stabilizer Off (Note 7)
Duty Cycle Stabilizer On (Note 7)
l
l
4.5
3
4.76
4.76
500
500
ns
ns
t
H
CLK High Time Duty Cycle Stabilizer Off (Note 7)
Duty Cycle Stabilizer On (Note 7)
l
l
4.5
3
4.76
4.76
500
500
ns
ns
t
AP
Sample-and-Hold Aperture Delay 0 ns
t
D
CLK to DATA Delay C
L
= 5pF (Note 7)
l
1.4 2.7 5.4 ns
t
MD
MUX to DATA Delay C
L
= 5pF (Note 7)
l
1.4 2.7 5.4 ns
Data Access Time After OE↓
C
L
= 5pF (Note 7)
l
4.3 10 ns
BUS Relinquish Time (Note 7)
l
3.3 8.5 ns
Pipeline Latency 5 Cycles
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to ground with GND and OGND
wired together (unless otherwise noted).
Note 3: When these pin voltages are taken below GND or above V
DD
, they
will be clamped by internal diodes. This product can handle input currents
of greater than 100mA below GND or above V
DD
without latchup.
Note 4: V
DD
= 3V, f
SAMPLE
= 105MHz, input range = 2V
P-P
with differential
drive, unless otherwise noted.
Note 5: Integral nonlinearity is defi ned as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 6: Offset error is the offset voltage measured from –0.5 LSB when
the output code fl ickers between 0000 0000 0000 and 1111 1111 1111.
Note 7: Guaranteed by design, not subject to test.
Note 8: V
DD
= 3V, f
SAMPLE
= 105MHz, input range = 1V
P-P
with differential
drive. The supply current and power dissipation are the sum total for both
channels with both channels active.
Note 9: Recommended operating conditions.
