2
AD7714
REV. C
–17–
Filter Registers. Power On/Reset Status: Filter High Register: 01␣ Hex. Filter Low Register: 40␣ Hex.
There are two 8-bit Filter Registers on the AD7714 from which data can either be read or to which data can be written. Tables IX
and X outline the bit designations for the Filter Registers.
Table IX. Filter High Register (RS2–RS0 = 0, 1, 0)
B/U WL BST ZERO FS11 FS10 FS9 FS8 A Versions
B/U WL BST CLKDIS FS11 FS10 FS9 FS8 Y Versions
Table X. Filter Low Register (RS2–RS0 = 0, 1, 1)
FS7 FS6 FS5 FS4 FS3 FS2 FS1 FS0 All Versions
B/U Bipolar/Unipolar Operation. A 0 in this bit selects Bipolar Operation. This is the default (Power-On or RESET)
status of this bit. A 1 in this bit selects unipolar operation.
WL Word Length. A 0 in this bit selects 16-bit word length when reading from the data register (i.e., DRDY returns
high after 16 serial clock cycles in the read operation). This is the default (Power-On or RESET) status of this
bit. A 1 in this bit selects 24-bit word length.
BST Current Boost. A 0 in this bit reduces the current taken by the analog front end. When the part is operated with
f
CLK IN
= 1␣ MHz or at gains of 1 to 4 with f
CLK IN
= 2.4576␣ MHz, this bit should be 0 to reduce the current
drawn from AV
DD
, although the device will operate just as well with this bit at a 1. When the AD7714 is oper-
ated at gains of 8 to 128 with f
CLK IN
= 2.4576␣ MHz, this bit must be 1 to ensure correct operation of the
device. The Power-On or RESET status of this bit is 0.
ZERO To ensure correct operation of the A Versions of the part, a 0 must be written to this bit.
CLKDIS Master Clock Disable Bit. A Logic 1 in this bit disables the master clock from appearing at the MCLKOUT
pin. When disabled, the MCLKOUT pin is forced low. This feature allows the user the flexibility of using the
MCLKOUT as a clock source for other devices in the system or for turning off the MCLKOUT as a power
saving feature. When using an external master clock or the MCLKIN pin, the AD7714 continues to have inter-
nal clocks and will convert normally with its CLKDIS bit active. When using a crystal oscillator or ceramic
resonator across the MCLK IN or MCLKOUT pins, the AD7714 clock is stopped and no conversions take
place when the CLKDIS bit is active.
FS11–FS0 Filter Selection. The on-chip digital filter provides a Sinc
3
(or (Sinx/x)
3
) filter response. The 12 bits of data
programmed into these bits determine the filter cut-off frequency, the position of the first notch of the filter and
the data rate for the part. In association with the gain selection, it also determines the output noise (and hence
the effective resolution) of the device.
The first notch of the filter occurs at a frequency determined by the relationship:
filter first notch frequency =␣ (f
CLK␣ IN
/128)/code
where code is the decimal equivalent of the code in bits FS0 to FS11 and is in the range 19 to 4,000. With the
nominal f
CLK IN
of 2.4576␣ MHz, this results in a first notch frequency range from 4.8␣ Hz to 1.01␣ kHz. To
ensure correct operation of the AD7714, the value of the code loaded to these bits must be within this range.
Failure to do this will result in unspecified operation of the device.
Changing the filter notch frequency, as well as the selected gain, impacts resolution. Tables I through IV show
the effect of the filter notch frequency and gain on the effective resolution of the AD7714. The output data rate
(or effective conversion time) for the device is equal to the frequency selected for the first notch of the filter. For
example, if the first notch of the filter is selected at 50␣ Hz then a new word is available at a 50 Hz rate or every
20␣ ms. If the first notch is at 1␣ kHz, a new word is available every 1␣ ms.
The settling time of the filter to a full-scale step input change is worst case 4 × 1/(output data rate). For
example, with the first filter notch at 50␣ Hz, the settling time of the filter to a full-scale step input change is
80␣ ms max. This settling time can be reduced to 3 × 1/(output data rate) by synchronizing the step input
change to a reset of the digital filter. In other words, if the step input takes place with the SYNC input low or
the FSYNC bit high, the settling time will be 3 × 1/(output data rate) from when SYNC returns high or
FSYNC returns low. If a change of channel takes place, the settling time is 3 × 1/(output data rate) regardless of
the SYNC or FSYNC status as the part issues an internal SYNC command when requested to change channels.
The –3 dB frequency is determined by the programmed first notch frequency according to the relationship:
filter –3 dB frequency = 0.262 × filter first notch frequency.