OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

W77I058A25PL

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P51P52-P54P55-P57P58-P60P61-P63P64-P66P67-P69P70-P72P73-P75P76-P78P79-P81P82-P82
W77IE58
Publication Release Date: October 20, 2005
- 13 - Revision A5
Power Control
Bit: 7 6 5 4 3 2 1 0
SM0D
SMOD0
- - GF1 GF0 PD IDL
Mnemonic: PCON Address: 87h
SMOD : This bit doubles the serial port baud rate in mode 1, 2, and 3 when set to 1.
SMOD0: Framing Error Detection Enable: When SMOD0 is set to 1, then SCON.7(SCON1.7)
indicates a Frame Error and acts as the FE(FE_1) flag. When SMOD0 is 0, then
SCON.7(SCON1.7) acts as per the standard 8052 function.
GF1-0: These two bits are general purpose user flags.
PD: Setting this bit causes the W77IE58 to go into the POWER DOWN mode. In this mode all the
clocks are stopped and program execution is frozen.
IDL: Setting this bit causes the W77IE58 to go into the IDLE mode. In this mode the clocks to the
CPU are stopped, so program execution is frozen. But the clock to the serial, timer and
interrupt blocks is not stopped, and these blocks continue operating.
Timer Condtrol
Bit: 7 6 5 4 3 2 1 0
TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0
Mnemonic: TCON Address: 88h
TF1: Timer 1 overflow flag: This bit is set when Timer 1 overflows. It is cleared automatically when
the program does a timer 1 interrupt service routine. Software can also set or clear this bit.
TR1: Timer 1 run control: This bit is set or cleared by software to turn timer/counter on or off.
TF0: Timer 0 overflow flag: This bit is set when Timer 0 overflows. It is cleared automatically when
the program does a timer 0 interrupt service routine. Software can also set or clear this bit.
TR0: Timer 0 run control: This bit is set or cleared by software to turn timer/counter on or off.
IE1: Interrupt 1 edge detect: Set by hardware when an edge/level is detected on
INT1. This bit is
cleared by hardware when the service routine is vectored to only if the interrupt was edge
triggered. Otherwise it follows the pin.
IT1: Interrupt 1 type control: Set/cleared by software to specify falling edge/ low level triggered
external inputs.
IE0: Interrupt 0 edge detect: Set by hardware when an edge/level is detected on
INT0 . This bit is
cleared by hardware when the service routine is vectored to only if the interrupt was edge
triggered. Otherwise it follows the pin.
IT0: Interrupt 0 type control: Set/cleared by software to specify falling edge/ low level triggered
external inputs.
W77IE58
- 14 -
Timer Mode Control
Bit: 7 6 5 4 3 2 1 0
GATE
CT/
M1 M0 GATE
CT/
M1 M0
TIMER1 TIMER0
Mnemonic: TMOD Address: 89h
GATE: Gating control: When this bit is set, Timer/counter x is enabled only while
INTx pin is high
and TRx control bit is set. When cleared, Timer x is enabled whenever TRx control bit is set.
CT/ : Timer or Counter Select: When cleared, the timer is incremented by internal clocks. When set
, the timer counts high-to-low edges of the Tx pin.
M1, M0: Mode Select bits:
M1 M0 Mode
0 0 Mode 0: 8-bits with 5-bit prescale.
0 1 Mode 1: 18-bits, no prescale.
1 0 Mode 2: 8-bits with auto-reload from THx
1 1 Mode 3: (Timer 0) TL0 is an 8-bit timer/counter controlled by the standard Timer 0
control bits. TH0 is a 8-bit timer only controlled by Timer 1 control bits. (Timer 1)
Timer/counter is stopped.
Timer 0 LSB
Bit: 7 6 5 4 3 2 1 0
TL0.7 TL0.6 TL0.5 TL0.4 TL0.3 TL0.2 TL0.1 TL0.0
Mnemonic: TL0 Address: 8Ah
TL0.7-0: Timer 0 LSB
Timer 1 LSB
Bit: 7 6 5 4 3 2 1 0
TL1.7 TL1.6 TL1.5 TL1.4 TL1.3 TL1.2 TL1.1 TL1.0
Mnemonic: TL1 Address: 8Bh
TL1.7-0: Timer 1 LSB
Timer 0 MSB
Bit: 7 6 5 4 3 2 1 0
TH0.7 TH0.6 TH0.5 TH0.4 TH0.3 TH0.2 TH0.1 TH0.0
Mnemonic: TH0 Address: 8Ch
TH0.7-0: Timer 0 MSB
W77IE58
Publication Release Date: October 20, 2005
- 15 - Revision A5
Timer 1 MSB
Bit: 7 6 5 4 3 2 1 0
TH1.7 TH1.6 TH1.5 TH1.4 TH1.3 TH1.2 TH1.1 TH1.0
Mnemonic: TH1 Address: 8Dh
TH1.7-0: Timer 1 MSB
Clock Control
Bit: 7 6 5 4 3 2 1 0
WD1 WD0 T2M T1M T0M MD2 MD1 MD0
Mnemonic: CKCON Address: 8Eh
WD1-0: Watchdog timer mode select bits: These bits determine the time-out period for the watchdog
timer. In all four time-out options the reset time-out is 512 clocks more than the interrupt time-
out period.
WD1 WD0 Interrupt time-out Reset time-out
0 0 2
17
2
17
+ 512
0 1 2
20
2
20
+ 512
1 0 2
23
2
23
+ 512
1 1 2
26
2
26
+ 512
T2M: Timer 2 clock select: When T2M is set to 1, timer 2 uses a divide by 4 clock, and when set to
0 it uses a divide by 12 clock.
T1M: Timer 1 clock select: When T1M is set to 1, timer 1 uses a divide by 4 clock, and when set to
0 it uses a divide by 12 clock.
T0M: Timer 0 clock select: When T0M is set to 1, timer 0 uses a divide by 4 clock, and when set to
0 it uses a divide by 12 clock.
MD2-0: Stretch MOVX select bits: These three bits are used to select the stretch value for the MOVX
instruction. Using a variable MOVX length enables the user to access slower external memory
devices or peripherals without the need for external circuits. The
RD or WR strobe will be
stretched by the selected interval. When accessing the on-chip SRAM, the MOVX instruction
is always in 2 machine cycles regardless of the stretch setting. By default, the stretch has
value of 1. If the user needs faster accessing, then a stretch value of 0 should be selected.
MD2 MD1 MD0 Stretch value MOVX duration
0 0 0 0 2 machine cycles
0 0 1 1 3 machine cycles (Default)
0 1 0 2 4 machine cycles
0 1 1 3 5 machine cycles
1 0 0 4 6 machine cycles
1 0 1 5 7 machine cycles
1 1 0 6 8 machine cycles
1 1 1 7 9 machine cycles
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P51P52-P54P55-P57P58-P60P61-P63P64-P66P67-P69P70-P72P73-P75P76-P78P79-P81P82-P82

W77I058A25PL

Mfr. #:
Buy W77I058A25PL
Manufacturer:
Description:
IC MCU 8BIT 32KB FLASH 44PLCC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet