OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

M95080-RMB6TG

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P49
M95160-x, M95080-x Delivery state
Doc ID 8028 Rev 11 25/49
7 Delivery state
7.1 Initial delivery state
The device is delivered with the memory array set at all 1s (FFh). The Status Register Write
Disable (SRWD) and Block Protect (BP1 and BP0) bits are initialized to 0.
8 Maximum rating
Stressing the device outside the ratings listed in Table 8. may cause permanent damage to
the device. These are stress ratings only, and operation of the device at these, or any other
conditions outside those indicated in the operating sections of this specification, is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Refer also to the STMicroelectronics SURE Program and other relevant
quality documents.
Table 8. Absolute maximum ratings
Symbol Parameter Min. Max. Unit
T
A
Ambient operating temperature –40 130 °C
T
STG
Storage temperature –65 150 °C
T
LEAD
Lead temperature during soldering See note
(1)
1. Compliant with JEDEC Std J-STD-020C (for small body, Sn-Pb or Pb assembly), the ST ECOPACK
®
7191395 specification, and the European directive on Restrictions on Hazardous Substances (RoHS)
2002/95/EU
°C
V
O
Output voltage –0.50 V
CC
+0.6 V
V
I
Input voltage –0.50 6.5 V
V
CC
Supply voltage –0.50 6.5 V
V
ESD
Electrostatic discharge voltage (human body model)
(2)
2. AEC-Q100-002 (compliant with JEDEC Std JESD22-A114, C1=100 pF, R1=1500 Ω, R2=500 Ω)
–4000 4000 V
DC and AC parameters M95160-x, M95080-x
26/49 Doc ID 8028 Rev 11
9 DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristic tables that
follow are derived from tests performed under the measurement conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 9. Operating conditions (M95160 and M95080)
Symbol Parameter Min. Max. Unit
V
CC
Supply voltage 4.5 5.5 V
T
A
Ambient operating temperature (device grade 6) –40 85 °C
Ambient operating temperature (device grade 3) –40 125 °C
Table 10. Operating conditions (M95160-W and M95080-W)
Symbol Parameter Min. Max. Unit
V
CC
Supply voltage 2.5 5.5 V
T
A
Ambient operating temperature (device grade 6) –40 85 °C
Ambient operating temperature (device grade 3) –40 125 °C
Table 11. Operating conditions (M95160-R and M95080-R)
Symbol Parameter Min. Max. Unit
V
CC
Supply voltage 1.8 5.5 V
T
A
Ambient operating temperature –40 85 °C
Table 12. Operating conditions (M95160-F)
(1)
1. Preliminary data.
Symbol Parameter Min. Max. Unit
V
CC
Supply voltage 1.7 5.5 V
T
A
Ambient operating temperature –40 85 °C
Table 13. AC measurement conditions
(1)
1. Output Hi-Z is defined as the point where data out is no longer driven.
Symbol Parameter Min. Typ. Max. Unit
C
L
Load capacitance 30 pF
Input rise and fall times 50 ns
Input pulse voltages 0.2V
CC
to 0.8V
CC
V
Input and output timing reference voltages 0.3V
CC
to 0.7V
CC
V
M95160-x, M95080-x DC and AC parameters
Doc ID 8028 Rev 11 27/49
Figure 14. AC measurement I/O waveform
Table 14. Capacitance
(1)
1. Sampled only, not 100% tested, at T
A
= 25 °C and a frequency of 5 MHz.
Symbol Parameter Test condition Min. Max. Unit
C
OUT
Output capacitance (Q) V
OUT
= 0 V 8 pF
C
IN
Input capacitance (D) V
IN
= 0 V 8 pF
Input capacitance (other pins) V
IN
= 0 V 6 pF
Table 15. DC characteristics (M95160 and M95080, device grade 3)
Symbol Parameter Test condition Min. Max. Unit
I
LI
Input leakage current V
IN
= V
SS
or
V
CC
± 2 µA
I
LO
Output leakage current S = V
CC
, V
OUT
= V
SS
or
V
CC
± 2 µA
I
CC
Supply current
C = 0.1V
CC
/0.9V
CC
at 5 MHz,
V
CC
= 5 V, Q = open
3mA
I
CC1
Supply current (Standby) S = V
CC
, V
CC
= 5 V, V
IN
= V
SS
or
V
CC
5µA
V
IL
Input low voltage –0.45 0.3 V
CC
V
V
IH
Input high voltage 0.7 V
CC
V
CC
+1 V
V
OL
(1)
1. For all 5 V range devices, the device meets the output requirements for both TTL and CMOS standards.
Output low voltage I
OL
= 2 mA, V
CC
= 5 V 0.4 V
V
OH
(1)
Output high voltage I
OH
= –2 mA, V
CC
= 5 V 0.8 V
CC
V
V
RES
(2)
2. Characterized only, not 100% tested.
Internal reset threshold
voltage
2.5 3.5 V
AI00825B
0.8V
CC
0.2V
CC
0.7V
CC
0.3V
CC
Input and Output
Timing Reference Levels
Input Levels
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P39P40-P42P43-P45P46-P48P49-P49

M95080-RMB6TG

Mfr. #:
Buy M95080-RMB6TG
Manufacturer:
STMicroelectronics
Description:
EEPROM 16 Kbit and 8 Kbit
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet